Search found 31 matches

by aleconakad
29 Mar 2019 13:07
Forum: Z-Uno
Topic: When can we expect release of 2.1.5?
Replies: 30
Views: 2430

Re: When can we expect release of 2.1.5?

thx, I just downloaded 2.1.5 and compared to 2.1.4 source code. Only 3 files have been changed: Mercury206Meter.cpp, LLCore_arduino.c, ZUNO_Definitions.h. Changes are minimal and are related to some internal logging events. I don't see any breaking changes in the API. Are you sure you have the lates...
by aleconakad
27 Mar 2019 16:31
Forum: Z-Uno
Topic: When can we expect release of 2.1.5?
Replies: 30
Views: 2430

Re: When can we expect release of 2.1.5?

Hi,

any beta release soon?
by aleconakad
13 Mar 2019 18:37
Forum: Z-Uno
Topic: Z-Uno: Trying to send Multi-level sensor report to Eurotronic Spirit TRV
Replies: 6
Views: 448

Re: Z-Uno: Trying to send Multi-level sensor report to Eurotronic Spirit TRV

Right, I've confused between BASIC_SET and BASIC_REPORT.
Thanks
by aleconakad
13 Mar 2019 18:33
Forum: Z-Uno
Topic: zunoSendReport in the Setup routine
Replies: 1
Views: 210

zunoSendReport in the Setup routine

I want in my sketch to revert the relays defined in channel 1 to 3 to the default state after a restart event. I do it like this: void setup() { relais1_state = 0; relais2_state = 0; relais3_state = 0; zunoSendReport (1); zunoSendReport (2); zunoSendReport (3); } void loop() { ... } byte relais1_get...
by aleconakad
11 Mar 2019 17:20
Forum: Z-Uno
Topic: Z-Uno: Trying to send Multi-level sensor report to Eurotronic Spirit TRV
Replies: 6
Views: 448

Re: Z-Uno: Trying to send Multi-level sensor report to Eurotronic Spirit TRV

I find this solution a bit dangerous because associating the Spirit to Z-Uno group 1 will not only send the Multilevel_Sensor_Report to it, but also all other defined channels in your Z-uno sketch. Please note that the Spirit supports Basic CC as follows: 0x00 Energy Save Heating 0x0F OFF No Heating...
by aleconakad
19 Feb 2019 16:34
Forum: Z-Uno
Topic: Compilation error - multiple-dynamic-1-wire-ds18b20-temperature-sensors
Replies: 2
Views: 226

Re: Compilation error - multiple-dynamic-1-wire-ds18b20-temperature-sensors

Did you try with Arduino 1.8.5?
I had only bad experience and strange behaviors with the 1.8.8, so I went back to 1.8.5.
by aleconakad
15 Feb 2019 18:47
Forum: Z-Uno
Topic: Zwave range and power
Replies: 21
Views: 2154

Re: Zwave range and power

Hi, I am facing the same issue here. I am using a Meanwell DIN 12V AC/DC power supply connected directly to 7-18V pin. Range is really miserable. With USB cable connected range is way better. Is there a way to control the power of the transmission of these modules. I am not sure about it but I think...
by aleconakad
14 Feb 2019 13:14
Forum: Z-Uno
Topic: When can we expect release of 2.1.5?
Replies: 30
Views: 2430

Re: When can we expect release of 2.1.5?

Thanks,

I am looking forward for the first beta. Can we expect it before end of February?
by aleconakad
07 Feb 2019 15:53
Forum: Z-Uno
Topic: Hardware Serial Ports modes
Replies: 3
Views: 267

Re: Hardware Serial Ports modes

Thanks,

it won't fit my needs as I need to reach 38400 in a 8E1 scheme. I will consider some dedicated SPI to UART chip.
by aleconakad
23 Jan 2019 19:12
Forum: Z-Uno
Topic: Hardware Serial Ports modes
Replies: 3
Views: 267

Hardware Serial Ports modes

Hi, currently I have a project that requires the usage of serial port at 19200 baud using the 8E1 (9-bit) scheme. To my understanding the HW serial ports on Z-Uno can only do 8N1. Is this a hardware restriction or a software one? In case it is a SW one, are there any plans to enable other encoding s...