Search found 10 matches

by joergm6
18 Nov 2017 20:21
Forum: Diskussion in Deutsch
Topic: Wie hoch ist der Datenverbrauch?
Replies: 2
Views: 108

Re: Wie hoch ist der Datenverbrauch?

genau wird dir das wohl Niemand sagen können, aber ich würde das kleinste Paket (nur Daten/Tablet-Notebookflat o.ö.) nehmen. Denn wenn dein Highspeed-Datenvolumen aufgebraucht ist, geht es immer noch mit 64kbit weiter. Auch das reicht locker für Status und Meldungen. Es werden ja nur kleine Datenmen...
by joergm6
12 Oct 2017 19:00
Forum: Z-Uno
Topic: Multiple buttons
Replies: 5
Views: 349

Re: Multiple buttons

Roughly overflown: I think there's a design flaw here. "if (Button5Reading == 0 && Button5Previous == 0" seems to be triggered again immediately. I'm using it like this. byte Button5Reading = digitalRead(Button5); if (Button5Reading != lastButton5State) { lastButton5State = Button5Reading; if (lastB...
by joergm6
05 Dec 2016 17:18
Forum: Z-Uno
Topic: Reboot board
Replies: 38
Views: 4806

Re: Reboot board

I have tried all ADC0-3 (Pin3-6), always the same problem (I do not know exactly whether I tried ADC2) :D
Yes, I mean the problem with the "turn off the digital PINs 19.-22" at transmission.
by joergm6
03 Dec 2016 19:21
Forum: Z-Uno
Topic: Reboot board
Replies: 38
Views: 4806

Re: Reboot board

Thank you for the information. I hope then on the next version.
I have observed a bit. ADC ALWAYS freezes when the Z controller is restarted. (Raspberry / Razberry2 / Domoticz). So must have something to do with the Z-Wave transmission. The digial PINs 19-22 also have a problem here.
by joergm6
30 Nov 2016 19:47
Forum: Z-Uno
Topic: Reboot board
Replies: 38
Views: 4806

Re: Reboot board

Yes, its 2.06 and the Z-Uno still works (4 switches). The code is not secret and basic code :). I have leave original example code of the Sharp still contain (distanceRead). Please try it, because it happens faster here. Currently, I read only once per second and add up to 10 passes. The end result ...
by joergm6
30 Nov 2016 16:22
Forum: Z-Uno
Topic: Reboot board
Replies: 38
Views: 4806

Re: Reboot board

I would also need such a reboot. The AD converters report sometimes the same value (and then forever 26cm). I can even remove the sensor, remains the reported value. There is no special time, but possibly with a lot of Z-Wave radio traffic. Often it happens when the Z-Controller is restarted, but al...
by joergm6
04 Nov 2016 01:10
Forum: Z-Uno
Topic: Digital output - pulse
Replies: 9
Views: 1007

Re: Digital output - pulse

you can have a look at a "Solid State Relais Modul Board".
These are small, switching completely electronically and the ready modules can be connected directly to the pins. The only question is which switching power is required.
... Oh, I'm too slow
by joergm6
03 Nov 2016 23:11
Forum: Z-Uno
Topic: Digital Output Pins 19-22
Replies: 8
Views: 1462

Re: Digital Output Pins 19-22

Thanks for the information. I had started with these pins to try and after a few hours ... I doubted myself :roll: :mrgreen: . But 9-12 is working and that is enough for me at the moment.
regards
by joergm6
03 Nov 2016 21:25
Forum: Z-Uno
Topic: Digital Output Pins 19-22
Replies: 8
Views: 1462

Digital Output Pins 19-22

Hello
I use 4 switches on pins 9-12 (digital-out). Everything works wonderful.
If I only change pins 9-12 to 19-22, everything else remains unchanged, then the outputs switch only shortly for a fraction of a second (LED flashes shortly).
Currently I need only 4 pins, but wanted to ask. :D
thank you