Search found 52 matches

by schmidmi
13 Jun 2018 10:19
Forum: Z-Uno
Topic: Zwave range and power
Replies: 3
Views: 652

Re: Zwave range and power

Maybe your DC is a little bit dirty and disturbing the Z-Wave communication.
You should try a different power supply.
by schmidmi
25 May 2018 17:55
Forum: Z-Uno
Topic: Scene control not working
Replies: 5
Views: 1046

Re: Scene control not working

Hi perjar, the problem was not on side of the Z-UNO. send the SceneActivation with an association to group 1 : zunoSendToGroupScene(1, persID); The parameter persID is just a value which can be read in the scene. But this is not all you have to do for getting the thing working with a HC2. You have t...
by schmidmi
18 May 2018 09:07
Forum: Z-Uno
Topic: Scene control not working
Replies: 5
Views: 1046

Re: Scene control not working

@perjar:
Hi,
I tried to get the scene activation working together with my HC2, but failed.
Do you have an example, how you were successful?

Update: Problem solved! It's working :D
by schmidmi
05 Nov 2017 01:21
Forum: Z-Uno
Topic: Problem with 2.1.1
Replies: 3
Views: 1148

Re: Problem with 2.1.1

After several retries of uploading the firmware and sketch, no it works fine. But I had to exclude and include the device in my HC 2.
Problem solved!
by schmidmi
05 Nov 2017 01:20
Forum: Z-Uno
Topic: Pin 5 in INPUT_PULLUP mode isn't pulled HIGH
Replies: 5
Views: 1448

Re: Pin 5 in INPUT_PULLUP mode isn't pulled HIGH

This problem is not only at pin 5. I had the same problem at pin 18. But the workaround works :)
by schmidmi
05 Nov 2017 00:05
Forum: Z-Uno
Topic: Problem with 2.1.1
Replies: 3
Views: 1148

Re: Problem with 2.1.1

I made some further investigations.
When not using my DS18B20 the sketch is not blocked anymore but still no connection to my HC2.
Do i have to exclude and include the device in my HC2?
by schmidmi
05 Nov 2017 00:02
Forum: Z-Uno
Topic: Problem with 2.1.1
Replies: 3
Views: 1148

Problem with 2.1.1

I did a upgrade of the Adruino IDE to 1.8.5. Then I installed the Z-UNO 2.1.1 board and made an upgrade for the bootloader on the Z-UNO. All these steps worked fine. Then I made a download of my sketch wich was running fine with Arduino 1.6.5 and Z_UNO 2.0.9. After about 2 cycles Z-UNO stops working...
by schmidmi
16 Oct 2017 17:05
Forum: Z-Uno
Topic: Mobile Z-Uno and connection loss
Replies: 7
Views: 1494

Re: Mobile Z-Uno and connection loss

I think, a robot which is moving around should be challenge for the network.
Because with respect to the conditions for the Z-wave signal, the device needs several different routes on its way through the house.
by schmidmi
12 Oct 2017 10:16
Forum: Z-Uno
Topic: Multiple buttons
Replies: 5
Views: 1399

Re: Multiple buttons

There is only one thing I can see:
You have some unnecessary brackets in your code.
The bracket before Serial.println("0. "); and after zunoSendReport(..); seem to be useless.
by schmidmi
06 Oct 2017 15:00
Forum: Z-Uno
Topic: New 2.1.1 test build is ready!
Replies: 17
Views: 4603

Re: New 2.1.1 test build is ready!

I think you mean "Arduino IDE 1.6.5 and 1.8.5 are now supported", isn't it?