Search found 323 matches

by michap
02 Jun 2018 10:36
Forum: Discussions in English
Topic: detect events of device in Z-Way
Replies: 0
Views: 600

detect events of device in Z-Way

Hi, for Sensative strips Comfort are different events defined for "high temperature alarm" and "low temperature alarm" So I get finally 3 events: SETDATA devices.8.instances.0.commandClasses.113.data.4.event = 6 (0x00000006) SETDATA devices.8.instances.0.commandClasses.113.data.4.event = 0 (0x000000...
by michap
02 Jun 2018 10:20
Forum: Discussions in English
Topic: Percent instead of Lux - Sensative Strips
Replies: 0
Views: 651

Percent instead of Lux - Sensative Strips

Hi, how can be changed the shown value for light in Lux, as expected by device? I now get percent - a bit high number ;) Sensative_strips_z-way_light.JPG In Log I see the right values [2018-06-01 15:25:16.905] [D] [zway] SETDATA devices.8.data.lastReceived = 0 (0x00000000) [2018-06-01 15:25:16.905] ...
by michap
23 May 2018 09:50
Forum: Z-Uno
Topic: I2C - Bus master clock stretching
Replies: 2
Views: 481

Re: I2C - Bus master clock stretching

Hi, https://ams.com/documents/20143/36005/iAQ-core_DS000334_1-00.pdf/f59e15ec-1716-72a8-cb23-fbdeaf0a24a0 At page 4 you can see: Although the module could send the bytes of data at a fast rate, it could happen that the module is busy at the request time. It can then hold the clock line low after rec...
by michap
21 May 2018 11:18
Forum: Z-Uno
Topic: I2C - Bus master clock stretching
Replies: 2
Views: 481

I2C - Bus master clock stretching

Hi, can somebody tell me for Z-Uno I2C - Bus master clock stretching is supported? Wire.setClockStretchLimit(1000); give me an error "error: no member named 'setClockStretchLimit'" Description about this clock stretching you can read here: https://www.i2c-bus.org/i2c-primer/clock-generation-stretchi...
by michap
03 May 2018 20:43
Forum: Diskussion in Deutsch
Topic: Devices testweise in einer anderen Homeautomatisierung benutzen
Replies: 7
Views: 1332

Re: Devices testweise in einer anderen Homeautomatisierung benutzen

... Ich will nur ungern die Dosen alle wieder auf und zu machen. Für jede Hilfe dankbar Hallo, man muss nicht die Dosen auf und zu machen ;) Aus dem Manual : include: "3) Triple click the B-button or a push button connected to the S1 terminal" Exclude: "3) Triple click the B-button or a push button...
by michap
02 May 2018 14:33
Forum: Z-Uno
Topic: OTA Sketch Upgrade
Replies: 10
Views: 1763

Re: OTA Sketch Upgrade

@donic46 : BTW: What Gateway you are using - with what relase?

Michael
by michap
01 May 2018 20:32
Forum: Z-Uno
Topic: FLiRS - flapping digital pins after wakeup
Replies: 15
Views: 2157

Re: FLiRS - flapping digital pins after wakeup

My solar based water valve for irrigation is working is working with such a relay ;) There are no problems at all. But I set the pins to LOW again after the delay to save energy - tried at first with wakeUp - but no stable success. The pin initialisation will be done only if the pin for the coil wil...
by michap
01 May 2018 19:33
Forum: Z-Uno
Topic: FLiRS - flapping digital pins after wakeup
Replies: 15
Views: 2157

Re: FLiRS - flapping digital pins after wakeup

I think you underestimate how many times setup() gets called... it is each time the device wakes up, and there are many reasons. It will wake up, for instance, when you "poll" the device because that is a radio transmission. so that will reset the pins and run setup(). Yes, right - but for this tes...
by michap
01 May 2018 19:09
Forum: Z-Uno
Topic: OTA Sketch Upgrade
Replies: 10
Views: 1763

Re: OTA Sketch Upgrade