Search found 61 matches

by Black Cat
19 Jun 2017 10:06
Forum: Z-Uno
Topic: converting from Arduino to Z-UNO simple code help needed
Replies: 5
Views: 2707

converting from Arduino to Z-UNO simple code help needed

Hello from a frustrated Z-UNO user. I have a simple Switch and Relay example from My Sensors site that will not compile in Z-UNO. Can anyone please help in converting this from Arduino to Z-UNO, apart from deleting the Radio, I'm lost concerning libraries required etc. * The MySensors Arduino librar...
by Black Cat
18 Jun 2017 00:10
Forum: Z-Uno
Topic: z-uno project from a standard uno board
Replies: 3
Views: 2223

Re: z-uno projet from a standard uno board

I think this is a valid point raised. There are many working examples of working projects written for Ardunio/Uno already in existence. The My Sensors site is full of them and has a very nice 16 Zone Irrigation Controller (amongst other projects) that would be more than useful with a ZUNO, but how d...
by Black Cat
17 Jun 2017 02:35
Forum: Z-Uno
Topic: Sketch not uploading
Replies: 2
Views: 1620

Re: Sketch not uploading

I found that a Factory reset eventually worked. Still took a long time, the Z-UNO instructions on Factory reset and Rescue Mode don't seem to be very clear in this respect.
by Black Cat
14 Jun 2017 01:53
Forum: Z-Uno
Topic: Sketch not uploading
Replies: 2
Views: 1620

Sketch not uploading

I have a sketch uploaded on ZUNO, however if I try to over write this with another different sketch, the original remains. The upload doesn't indicate failure however the new sketch is not uploaded. Something is preventing overwriting. How can I erase the sketch that is in ZUNO and upload a new sket...
by Black Cat
13 Jun 2017 05:54
Forum: Z-Uno
Topic: 4 Ch. Relay with Switches Some help required with sketch
Replies: 9
Views: 4114

Re: 4 Ch. Relay with Switches Some help required with sketch

Got it half working.

Relays will set state from UI, there is a problem with the loop as it doesn't detect the button when it is pushed.

The only other change was that I put a pullup resistor in the circuit for the buttons.
by Black Cat
13 Jun 2017 05:18
Forum: Z-Uno
Topic: 4 Ch. Relay with Switches Some help required with sketch
Replies: 9
Views: 4114

Re: 4 Ch. Relay with Switches Some help required with sketch

Found it. I used mixed Uppercase and lower case.
by Black Cat
13 Jun 2017 05:01
Forum: Z-Uno
Topic: 4 Ch. Relay with Switches Some help required with sketch
Replies: 9
Views: 4114

Re: 4 Ch. Relay with Switches Some help required with sketch

/* * * 4 Relays controlled thouth resistors 220Omh and optocouplers 817С 4 On/Off Switches * Off - HIGH * On - LOW */ // Pins definitions #define RelayPin1 9 #define RelayPin2 10 #define RelayPin3 11 #define RelayPin4 12 #define BTN_PIN1 19 // switch pin19 #define BTN_PIN2 20 // switch pin20 #defin...
by Black Cat
13 Jun 2017 03:45
Forum: Z-Uno
Topic: 4 Ch. Relay with Switches Some help required with sketch
Replies: 9
Views: 4114

Re: 4 Ch. Relay with Switches Some help required with sketch

Association Control3.jpg
Association Control3.jpg (49.73 KiB) Viewed 4094 times
by Black Cat
13 Jun 2017 03:43
Forum: Z-Uno
Topic: 4 Ch. Relay with Switches Some help required with sketch
Replies: 9
Views: 4114

Re: 4 Ch. Relay with Switches Some help required with sketch

In the sketch the /b is not present. I have edited it out above.
by Black Cat
13 Jun 2017 03:22
Forum: Z-Uno
Topic: 4 Ch. Relay with Switches Some help required with sketch
Replies: 9
Views: 4114

Re: 4 Ch. Relay with Switches Some help required with sketch

Thanks, that part is now clear. Next problem is definition again, this time in the loop. void loop() { byte currentValue = !digitalRead(BTN_PIN1); if (currentValue != lastValue) { // if state changes lastValue = currentValue; // save new state if (lastValue) { zunoSendToGroupSetValueCommand(CTRL_GRO...