Static PC Controller Configuration

Discussions about RaZberry - Z-Wave board for Raspberry computer
Post Reply
User avatar
marco
Posts: 85
Joined: 03 Dec 2015 19:50

Static PC Controller Configuration

Post by marco »

Hi All, is there any one that can explain why, in the interview page of the zway configuration section (expert UI), choosing razberry as device id 1, I can not complete interview and I always read "Device seems to be dead"?
According to log file, after a Foce Interview call, I have
"
SETDATA devices.1.instances.0.commandClasses.152.data.interviewDone = False
[2016-04-18 06:03:58.527] [D] [zway] SETDATA devices.1.instances.0.commandClasses.152.data.interviewCounter = 9 (0x00000009)
[2016-04-18 06:03:58.528] [zway] Node 1:0 CC Security Interview started
[2016-04-18 06:03:58.528] [zway] Node 1:0 CC Security: sending Scheme Get
[2016-04-18 06:03:58.528] [E] [zway] Dropping packet to myself (node 1)
[2016-04-18 06:03:58.528] [E] [zway] Error returned from (command->cc->interview_handler)(zway, command): Not implemented by the library (-3)

"
Is this normal?
Thanks
Marco
Attachments
Screen Shot
Screen Shot
Cattura.JPG (109.71 KiB) Viewed 8757 times
Marco
kandalf
Posts: 54
Joined: 13 May 2016 11:10

Re: Static PC Controller Configuration

Post by kandalf »

Hi there,
since yesterday i would setup my raspberry new and install a fresh sd card, now i have the same problem.
Have you more information about the problem?
Raspberry PI with Z-Wave.me Board
2 x Fibaro Double Relay-Switch FGS 222
2 x Fibaro Shutter FGR 222
Fibaro Multi Sensor
Z-Wave.me RemoteControl
User avatar
marco
Posts: 85
Joined: 03 Dec 2015 19:50

Re: Static PC Controller Configuration

Post by marco »

Hi Kandalf,
I'm sorry, no news from my side
Marco
kandalf
Posts: 54
Joined: 13 May 2016 11:10

Re: Static PC Controller Configuration

Post by kandalf »

It was a mistake, that only comes when you have no device included. It is a view problem.
When you look at controller information you can see that all is ok.

So include one device and then in the configuration list you can see the new device and all is fine.
Raspberry PI with Z-Wave.me Board
2 x Fibaro Double Relay-Switch FGS 222
2 x Fibaro Shutter FGR 222
Fibaro Multi Sensor
Z-Wave.me RemoteControl
User avatar
marco
Posts: 85
Joined: 03 Dec 2015 19:50

Re: Static PC Controller Configuration

Post by marco »

For me it was not properly like this. At the moment I'have no more this reporting status (it disappeard on a previous upgrading) but in the past it was appearing even if I had 15-20 devices included. Probably there is a relation with the software release but I don't know the causes.
Marco
User avatar
PoltoS
Posts: 7565
Joined: 26 Jan 2011 19:36

Re: Static PC Controller Configuration

Post by PoltoS »

Are you trying to interview #1 from #1 ? it will not reach itself through radio ;)

In fact the #1 selection in Configuration tab gices you no info. You don't need it. In latest Z-Way we have even decided to hide it not to frustrate users.
User avatar
marco
Posts: 85
Joined: 03 Dec 2015 19:50

Re: Static PC Controller Configuration

Post by marco »

thanks,
Marco
Marco
Post Reply