1) My StellaZ (Device_9) is in Expert UI shown as Switch - what can I switch there?
Uwe
2) It is also shown as Thermostat - but there is nothing to set?
The illustration as Sensor data is ok.
Is the StellaZ not fully supported in V2.0.0? If yes, I hope it is on the todo-list StellaZ in V2.0.0
StellaZ in V2.0.0
Last edited by LAN-Opfer on 12 Dec 2014 15:23, edited 3 times in total.
Z-Way v2.0.1-rc18 on Raspberry Pi
Re: StellaZ in V2.0.0
StellaZ has four mode settings
Comfort, SaveHeat, Frost protect, and direct valve control.
The direct valve control is seen as a dimmer'type device, which by its nature you can swith on and off.
Before you can set the valve, the StellaZ must be placed in that direct control modus. Same aplies for setting temperature for Comfort/SaveHeat.
Unfortunately none of these are available yet in the scenes/rules modules.
Comfort, SaveHeat, Frost protect, and direct valve control.
The direct valve control is seen as a dimmer'type device, which by its nature you can swith on and off.
Before you can set the valve, the StellaZ must be placed in that direct control modus. Same aplies for setting temperature for Comfort/SaveHeat.
Unfortunately none of these are available yet in the scenes/rules modules.
Since 29-12-2016 I am no longer a moderator for this forum
Re: StellaZ in V2.0.0
...ah - ok. I think about, to use the direkt mode because I use for the same heating a extra Thermostat as remote control. It is not ideal, to use the sensor near the heating for temperature control. I will use a script as PI-controller - but that is a todo in future.
But what about Thermostat? Device_9 is not able to set as thermostat
...sorry - I see, that I did a mistake with the pictures...
I have now the right pictures in my first post.
Uwe
But what about Thermostat? Device_9 is not able to set as thermostat
...sorry - I see, that I did a mistake with the pictures...
I have now the right pictures in my first post.
Uwe
Z-Way v2.0.1-rc18 on Raspberry Pi
Re: StellaZ in V2.0.0
Print in the images is to small for my old eyes.LAN-Opfer wrote: But what about Thermostat? Device_9 is not able to set as thermostat
...sorry - I see, that I did a mistake with the pictures...
The thermostat view in the new Expert UI seems still incomplete.
I do use the Old Expert UI for special manual thermostat settings.
In daily use it is controlled from OpenRemote Android client
Since 29-12-2016 I am no longer a moderator for this forum
Re: StellaZ in V2.0.0
...a Little small - that's true, but my eyes are already 50 years old and can recognize it yet - maybe I should write in Braille nowpz1 wrote:Print in the images is to small for my old eyes.
...that is very interesting - I will have a look to it!pz1 wrote:In daily use it is controlled from OpenRemote Android client
Uwe
Z-Way v2.0.1-rc18 on Raspberry Pi
Re: StellaZ in V2.0.0
Created an issue: https://github.com/Z-Wave-Me/ExpertUI/issues/45
We hope to fix this within a week or two
We hope to fix this within a week or two
Re: StellaZ in V2.0.0
...I installed the Android-App - but I am not able to configure it Do you have some tips, what I have to do?pz1 wrote:In daily use it is controlled from OpenRemote Android client
Uwe
Z-Way v2.0.1-rc18 on Raspberry Pi
Re: StellaZ in V2.0.0
Add new profile and search for boxes in your network