Search found 8 matches
- 12 Jun 2013 18:03
- Forum: RaZberry
- Topic: 2Gig CT-100 Inteview Not Complete
- Replies: 19
- Views: 16177
Just an fyi, i sent the logs
Just an fyi, i sent the logs on this same problem in april (april 6th).Was told it was a problem in the razberry software and would get a follow up after an investigation. Was checking back (7 months later) to see if this and my door lock had ever received support... guess not
- 26 Apr 2013 00:39
- Forum: RaZberry
- Topic: GE/Jasco Binary & Dimmer Switches
- Replies: 9
- Views: 8460
GE/Jasco Binary & Dimmer Switches
<r>I have a bunch of GE/Jasco Binary and Dimmer switches - model #'s 456xx<br/> <br/> My question is, does anyone know if these should send a power status update to the controller when manually switched on or off? I am running into a problem with my automation engine when actions are dependent upon ...
- 26 Apr 2013 00:39
- Forum: RaZberry
- Topic: GE/Jasco Binary & Dimmer Switches
- Replies: 9
- Views: 8460
What model switches do you
<t>What model switches do you have neobaud? I have 3 way binary, 3 way dimmer, single dimmer & binary... pretty much the whole slew...<br/> <br/> When i run the following command:<br/> /ZWaveAPI/Data/1367016866<br/> <br/> I get no updates at all when walking up to any switch and flipping it on a...
- 26 Apr 2013 00:39
- Forum: RaZberry
- Topic: GE/Jasco Binary & Dimmer Switches
- Replies: 9
- Views: 8460
.
<t>I think PoltoS is correct. I have been doing some research on the interwebs and i think it is the case it is one way polling. That is quite a bummer considering the amount of cash they make you drop on these bad boys. <br/> <br/> I think i am going to have to custom make a sensor (implement a xbe...
- 12 Apr 2013 08:43
- Forum: RaZberry
- Topic: Listening IP
- Replies: 1
- Views: 3398
Listening IP
Is there a config setting to restrict the application to a specific IP to listen on?
- 08 Apr 2013 18:21
- Forum: RaZberry
- Topic: Razberry Promiscuous
- Replies: 4
- Views: 6174
.
<t>So, if i can relate to my experience with ZigBee/Xbee... (and i am not 100% sure this is the answer, just shooting from the hip)<br/> <br/> With Xbee, there is a mcu on the board (board: in this case the razberry) which handles a bulk of the low level communication. Only when unsupported or speci...
- 08 Apr 2013 12:14
- Forum: RaZberry
- Topic: Automation / schedule NEWBIE
- Replies: 1
- Views: 3388
.
As far as I understand, the automation piece hasn't been implemented on the razberry platform yet.
- 07 Apr 2013 02:20
- Forum: RaZberry
- Topic: Sending a climate control schedule to Danfoss thermostat?
- Replies: 5
- Views: 18326
.
Trying to figure out my thermostat also... This should get you the set point though:
devices[#].instances[#].ThermostatSetPoint.data[MODE#].setVal.value
...
devices[5].instances[0].ThermostatSetPoint.data[1].setVal.value
devices[#].instances[#].ThermostatSetPoint.data[MODE#].setVal.value
...
devices[5].instances[0].ThermostatSetPoint.data[1].setVal.value