I mean how do you figure out the system is corrupted? How do you check?
Your initial message indicated that you checked sda1 and sda2, and both are clean.
Search found 38 matches
- 19 Mar 2016 18:34
- Forum: RaZberry
- Topic: Repeated corruption of SDcards
- Replies: 37
- Views: 33979
- 19 Mar 2016 00:09
- Forum: RaZberry
- Topic: Repeated corruption of SDcards
- Replies: 37
- Views: 33979
Re: Repeated corruption of SDcards
Nice. So what was different in the "new" setup?
Your SD Card, Pi board and UZB stick are all new? Does that mean the same power supply?
Btw, how does the corruption look like? I mean why do you think it's corrupted?
Your SD Card, Pi board and UZB stick are all new? Does that mean the same power supply?
Btw, how does the corruption look like? I mean why do you think it's corrupted?
- 18 Mar 2016 20:30
- Forum: RaZberry
- Topic: Repeated corruption of SDcards
- Replies: 37
- Views: 33979
Re: Repeated corruption of SDcards
The card looks OK for an average Class 10 card. I could only guess that there is some weird incompatibility with Pi using this card. I know it's a hassle, but: If you swap the cards with your good working Pi setup and this one, do the corruption problems move to another Pi or stay there? Just trying...
- 17 Mar 2016 23:32
- Forum: Обсуждение на русском / Discussions in Russian
- Topic: Доступ через https
- Replies: 5
- Views: 8067
Re: Доступ через https
Да, stunnel должен быть с двух сторон, так как он шифрует всё, а в случае с https заголовки не шифруются.
Если нужно видеть как https без настроек на стороне клиента, то nginx с upstream/proxy_pass -- лучший вариант в этом случае.
Если нужно видеть как https без настроек на стороне клиента, то nginx с upstream/proxy_pass -- лучший вариант в этом случае.
- 17 Mar 2016 23:20
- Forum: RaZberry
- Topic: Repeated corruption of SDcards
- Replies: 37
- Views: 33979
Re: Repeated corruption of SDcards
15 MB/s sounds reasonable for Class 10 card.
So I guess it's just a matter of checking it using h2testw (probably will pass, but anyway) and trying another brand card.
So I guess it's just a matter of checking it using h2testw (probably will pass, but anyway) and trying another brand card.
- 17 Mar 2016 19:14
- Forum: RaZberry
- Topic: Repeated corruption of SDcards
- Replies: 37
- Views: 33979
Re: Repeated corruption of SDcards
Could this high update rate cause problems with the SDCard? I'd be surprised if that causes the corruption on the card, unless the card is defective by itself. I have other tasks running on my Pi, and those tasks usually write/update even more often without any corruption issues at all. Did you hav...
- 17 Mar 2016 08:39
- Forum: Discussions in English
- Topic: Improve UZB-Stick signal strength/sensitivity
- Replies: 2
- Views: 5779
Re: Improve UZB-Stick signal strength/sensitivity
Depending on your needs, just as another alternative maybe you should try a Z-Wave extender.
- 17 Mar 2016 08:34
- Forum: Discussions in English
- Topic: Not able to access Expert UI from Port 8084
- Replies: 11
- Views: 19289
Re: Not able to access Expert UI from Port 8084
Yes, ports 8084 and 443 are used by mongoose process. The expert UI is http://192.168.1.100:8083/expert (replace "192.168.1.100" with the IP of your server) Or you can also access the expert UI by navigating Gear icon -> Devices -> Manage with ExpertUI. Although, it's not always there acco...
- 17 Mar 2016 04:33
- Forum: Обсуждение на русском / Discussions in Russian
- Topic: Доступ через https
- Replies: 5
- Views: 8067
Re: Доступ через https
z-way-server (порт 8083) бинарник не использует SSL библиотеки (по-крайне мере, динамические) и вряд ли поддерживает SSL в этом случае. На 8084 и 443 сидит mongoose, но он вроде как напрямую не используется для API z-way. Тут только если тунель делать. Например, stunnel . Он сможет принять SSL трафи...
- 17 Mar 2016 04:23
- Forum: RaZberry
- Topic: Rasberry PI 3 supported?
- Replies: 29
- Views: 58142
Re: Rasberry PI 3 supported?
If you are fine with Bluetooth disabled but want to have WiFi operational anyway, you can do the following (must be root or use sudo): 1. Make sure you are on the latest kernel and have the latest overlay files: rpi-update 2. Add "disable BT" overlay: echo "dtoverlay=pi3-disable-bt&qu...