Search found 9 matches

by Quikdav
22 Sep 2016 19:51
Forum: Z-Uno
Topic: Power supply on 5V pin / 3.3V pin
Replies: 3
Views: 2144

Re: Power supply on 5V pin / 3.3V pin

PoltoS wrote:Yes, you can connect power to 5V or 3V3 pins directly

For 5->3.3 DC-DC we use MCP1700. It can source up to 250 mA total
it's a good news to be able to avoid micro USB as power input ;-)
by Quikdav
22 Sep 2016 19:47
Forum: Z-Uno
Topic: Many subdevices after inclusion on Fibaro HC2
Replies: 4
Views: 2583

Re: Many subdevices after inclusion on Fibaro HC2

My HC version is 4.090....

I thought that with 7 channels, I should have one main device and 7 child devices...so every 708.x child devices was normal but it is not the case...

I will create a ticket to fibaro support for more information
by Quikdav
22 Sep 2016 14:48
Forum: Z-Uno
Topic: Many subdevices after inclusion on Fibaro HC2
Replies: 4
Views: 2583

Many subdevices after inclusion on Fibaro HC2

Hi All I modified the 10 channels sketch to create my own with only 7 channels. ZUNO_SETUP_CHANNELS( ZUNO_SWITCH_BINARY(getterSwitch1, setterSwitch1), ZUNO_SWITCH_BINARY(getterSwitch2, setterSwitch2), ZUNO_SWITCH_BINARY(getterSwitch3, setterSwitch3), ZUNO_SENSOR_MULTILEVEL_CO2_LEVEL(getterMonoxyde),...
by Quikdav
10 Sep 2016 09:53
Forum: Z-Uno
Topic: Z-Uno and debuging?
Replies: 10
Views: 6749

Re: Z-Uno and debuging?

oups I forgot this information :-(

Ok I added a delay of 31s and it seems working fine... but mayne a bypass would be a good idea for some sensors like CO2, fire, luminance and so on...
by Quikdav
10 Sep 2016 00:42
Forum: Z-Uno
Topic: Z-Uno and debuging?
Replies: 10
Views: 6749

Re: Z-Uno and debuging?

Very good news, everything is working fine now.. I installed again arduino IDE to be sure USB drivers were well installed Then I upgrade to 2.05. I was in 0.67 !!! I understood available and proposed versions depend on the url you suggested, right ? The serial output window is fine too, I can see va...
by Quikdav
09 Sep 2016 10:30
Forum: Z-Uno
Topic: Z-Uno and debuging?
Replies: 10
Views: 6749

Re: Z-Uno and debuging?

Thanks a lot for all these informations. Hope it will works. You'are right for all my versions ;-)
I spent 3 hours yesterday with port issues. Very frustrating :-(
I will follow your recommendations this week end and will inform you about the result...
by Quikdav
08 Sep 2016 23:48
Forum: Z-Uno
Topic: Z-Uno and debuging?
Replies: 10
Views: 6749

Re: Z-Uno and debuging?

So I added following code within Certified 10 Channels Sketch. When I open the console from arduino IDE, I don't have anything !!! // Luminosity Serial.println("valeur: "); Serial.println(analogRead(LumiPin)); currentLumiValue = (byte)(100 - analogRead(LumiPin)*25/256); if ((currentLumiValue > (last...
by Quikdav
08 Sep 2016 22:35
Forum: Z-Uno
Topic: Z-Uno and debuging?
Replies: 10
Views: 6749

Re: Z-Uno and debuging?

thanks for the reply... yes I just want to check the value from the sensor (to konow if it is compatible first and if I get date from it)... So I add the command but now I have an other issue.. I can't upload the sketch. Everything seems to be ok for the port, I selected it but it is written "Disabl...
by Quikdav
08 Sep 2016 22:08
Forum: Z-Uno
Topic: Z-Uno and debuging?
Replies: 10
Views: 6749

Re: Z-Uno and debuging?

Hi

same for me. How can we check data we are processing. I use a Grove light sensor and I would like to check if it works with Certified 10 Channels Sketch

Thanks