Search found 55 matches
- 17 Feb 2020 13:36
- Forum: Z-Uno
- Topic: Problems with reports to HC2 in 2.1.5
- Replies: 2
- Views: 11728
Problems with reports to HC2 in 2.1.5
I made a small application to monitor my consumption of electrical energy to show it in Fibaro HC2. In the first step the Z-UNO code was developed on FW 2.1.4 and seemed to work well. There are 2 channels defined like this: #define ZUNO_CHANNEL_NUMBER_Watts 1 #define ZUNO_CHANNEL_NUMBER_KWh 2 ZUNO_S...
- 25 Jan 2020 18:01
- Forum: Z-Uno
- Topic: Z wave to IR. Unknown IR
- Replies: 4
- Views: 6208
Re: Z wave to IR. Unknown IR
I had a similar problem with my Mitsubishi AC unit. It was a hard work to inculde this into my Z-Wave network, because it uses telegrams with 128 bits. There where several steps to the success: 1. I baugt a nice software tool for analysing the the telegrams, see here https://www.analysir.com/blog/ 2...
- 21 Jan 2020 16:30
- Forum: Z-Uno
- Topic: Z wave to IR. Unknown IR
- Replies: 4
- Views: 6208
Re: Z wave to IR. Unknown IR
Which AC unit are you using?
- 13 Jun 2018 10:19
- Forum: Z-Uno
- Topic: Zwave range and power
- Replies: 21
- Views: 19614
Re: Zwave range and power
Maybe your DC is a little bit dirty and disturbing the Z-Wave communication.
You should try a different power supply.
You should try a different power supply.
- 25 May 2018 17:55
- Forum: Z-Uno
- Topic: Scene control not working
- Replies: 5
- Views: 6221
Re: Scene control not working
Hi perjar, the problem was not on side of the Z-UNO. send the SceneActivation with an association to group 1 : zunoSendToGroupScene(1, persID); The parameter persID is just a value which can be read in the scene. But this is not all you have to do for getting the thing working with a HC2. You have t...
- 18 May 2018 09:07
- Forum: Z-Uno
- Topic: Scene control not working
- Replies: 5
- Views: 6221
Re: Scene control not working
@perjar:
Hi,
I tried to get the scene activation working together with my HC2, but failed.
Do you have an example, how you were successful?
Update: Problem solved! It's working
Hi,
I tried to get the scene activation working together with my HC2, but failed.
Do you have an example, how you were successful?
Update: Problem solved! It's working
- 05 Nov 2017 01:21
- Forum: Z-Uno
- Topic: Problem with 2.1.1
- Replies: 3
- Views: 4459
Re: Problem with 2.1.1
After several retries of uploading the firmware and sketch, no it works fine. But I had to exclude and include the device in my HC 2.
Problem solved!
Problem solved!
- 05 Nov 2017 01:20
- Forum: Z-Uno
- Topic: Pin 5 in INPUT_PULLUP mode isn't pulled HIGH
- Replies: 5
- Views: 5542
Re: Pin 5 in INPUT_PULLUP mode isn't pulled HIGH
This problem is not only at pin 5. I had the same problem at pin 18. But the workaround works
- 05 Nov 2017 00:05
- Forum: Z-Uno
- Topic: Problem with 2.1.1
- Replies: 3
- Views: 4459
Re: Problem with 2.1.1
I made some further investigations.
When not using my DS18B20 the sketch is not blocked anymore but still no connection to my HC2.
Do i have to exclude and include the device in my HC2?
When not using my DS18B20 the sketch is not blocked anymore but still no connection to my HC2.
Do i have to exclude and include the device in my HC2?
- 05 Nov 2017 00:02
- Forum: Z-Uno
- Topic: Problem with 2.1.1
- Replies: 3
- Views: 4459
Problem with 2.1.1
I did a upgrade of the Adruino IDE to 1.8.5. Then I installed the Z-UNO 2.1.1 board and made an upgrade for the bootloader on the Z-UNO. All these steps worked fine. Then I made a download of my sketch wich was running fine with Arduino 1.6.5 and Z_UNO 2.0.9. After about 2 cycles Z-UNO stops working...