Search found 28 matches
- 14 May 2018 13:04
- Forum: Z-Uno
- Topic: Channel report is corrupted while transferred from zuno to controller
- Replies: 4
- Views: 4627
Re: Channel report is corrupted while transferred from zuno to controller
Tried to enable security - s2 does not work for mw since it leaves only 6K for sketch while it is 21K size. With s0 enabled, z-uno just hangs after some time (may be stack issue , sketch is big enough)
- 04 May 2018 16:21
- Forum: Z-Uno
- Topic: Channel report is corrupted while transferred from zuno to controller
- Replies: 4
- Views: 4627
Re: Channel report is corrupted while transferred from zuno to controller
Thx.
Changing controller is not an option for me. But security is a good point will try it.
Changing controller is not an option for me. But security is a good point will try it.
- 12 Apr 2018 09:09
- Forum: Z-Uno
- Topic: Channel report is corrupted while transferred from zuno to controller
- Replies: 4
- Views: 4627
Channel report is corrupted while transferred from zuno to controller
I have ds18b20 connected to z-uno and sketch that reports temperature each 30s. Temperature rounded to have one fractional digit (21,86 is reported as 21.9). CRC from ds18b20 is checked and if does not match value is not reported. z-uno is connected to fibaro hc2. Occasionally hc2 gets wrong values ...
- 03 Jan 2018 02:39
- Forum: Z-Uno
- Topic: Z-Uno as a modem example compiles with errors
- Replies: 0
- Views: 3038
Z-Uno as a modem example compiles with errors
I've downloaded modem example from here https://z-uno.z-wave.me/examples/z-uno-as-a-modem/ Z-Uno software version 2.1.1 Compilation fails... Compiling zuno-modem_sdcpp_.cpp ... zuno-modem:112: error: member reference type '_xd_zuno_sketch_t' (aka 'zuno_sketch_s') is not a pointer; did you mean to us...
- 11 Dec 2017 15:48
- Forum: Z-Uno
- Topic: z-wave communication occasionally stops
- Replies: 3
- Views: 4649
Re: z-wave communication occasionally stops
Yes 2.1.1
How can I check the attach usage, are there any way to get exact values, or staring at the code is only available analysis?
How can I check the attach usage, are there any way to get exact values, or staring at the code is only available analysis?
- 08 Dec 2017 12:33
- Forum: Z-Uno
- Topic: Real size of flash memory
- Replies: 4
- Views: 4704
Re: Real size of flash memory
Sent you the link to code as private message
- 07 Dec 2017 12:38
- Forum: Z-Uno
- Topic: Real size of flash memory
- Replies: 4
- Views: 4704
Re: Real size of flash memory
I can confirm this behavior, lost lots of time before understood that if binary size exceeds 30K upload procedure passes but does not change the binary on z-uno.
- 07 Dec 2017 12:29
- Forum: Z-Uno
- Topic: z-wave communication occasionally stops
- Replies: 3
- Views: 4649
z-wave communication occasionally stops
Ran into following situation: z-uno is registered in z-wave network (controller - fibaro) It exposes multiple - bin switches , power meter and for diagnostics purpose uptime sensor (sensor reporting seconds since z-uno start). At some point value of sensor stopped changing, device stopped reacting o...
- 05 Dec 2017 03:09
- Forum: Z-Uno
- Topic: Radio logging documentation
- Replies: 0
- Views: 2558
Radio logging documentation
On Arduino IDE there is a setting "Logging" with "radio" option. Is there any doc describing how it works?
- 04 Dec 2017 19:07
- Forum: Z-Uno
- Topic: Electricity meter using ZUNO_METER
- Replies: 13
- Views: 15026
Re: Electricity meter using ZUNO_METER
Just solved quite similar problem - device is on din rail in boiler room controls 8 energy consumers (5 circulation pumps, well pump, filtering system etc). 8 relay controlled loads in total. I used acs712 (http://henrysbench.capnfatz.com/henrys-bench/arduino-current-measurements/acs712-current-sens...