Search found 10 matches
- 20 Nov 2023 14:55
- Forum: Z-Uno
- Topic: Battery powered light toggle
- Replies: 1
- Views: 46675
Battery powered light toggle
Hi, I'm trying to build a simple battery powered light toggle. I have a light connected to a z-wave smart wall switch. I would like to be able to toggle it on/off from another place with a battery powered switch. I connected the Z-uno to a simple door bell switch and loaded this sketch: byte buttonP...
- 06 Oct 2019 20:04
- Forum: RaZberry
- Topic: External Antenna on Razberry 2
- Replies: 2
- Views: 5114
Re: External Antenna on Razberry 2
Would be nice to have an updated manual for this version of the board. I spent a few days trying to figure this out.
- 05 Oct 2019 14:28
- Forum: RaZberry
- Topic: External Antenna on Razberry 2
- Replies: 2
- Views: 5114
External Antenna on Razberry 2
Hi, I decided to install an external antenna on my Razberry. I have one of the elements in my garden and I had problems to connect with it. I followed the instructions to solder an u.fl connector and break of the PCB antenna. I connected an external antenna dedicated for Z-wave. At this moment I los...
- 01 May 2019 15:49
- Forum: Recipes
- Topic: [userModule] Condition Switch (Updated 2017/02/02)
- Replies: 17
- Views: 44448
Re: [userModule] Condition Switch (Updated 2017/02/02)
Hi, I have an issue using this module. I've set a rule for garden lights. I wanted to be able to switch them also manually so I created a virtual switch for them. The rule is: Virtual switch on OR ( solar attitude < 5 AND time between 12pm and 0:00). This works fine overall, but when the lights are ...
- 09 Jan 2019 14:15
- Forum: Z-Uno
- Topic: Color Switch in Z-uno for RGB leds
- Replies: 4
- Views: 4599
Re: Color Switch in Z-uno for RGB leds
I don't use PWM to control the LEDs. I have WS2811 Led strips. I use this code to get the RGB values from the controller: ZUNO_SETUP_CHANNELS(ZUNO_SWITCH_COLOR(SWITCH_COLOR_FLAGS_RED|SWITCH_COLOR_FLAGS_GREEN|SWITCH_COLOR_FLAGS_BLUE, getColor, setColor)); void setColor (byte color,byte value){ switch...
- 08 Jan 2019 16:08
- Forum: Z-Uno
- Topic: Bootloader mismatch
- Replies: 5
- Views: 6251
Re: Bootloader mismatch
Have you installed in the Arduino IDE the latest Z-Uno libraries? I think the the latest Z-uno Core is 2.1.3.
- 07 Jan 2019 16:35
- Forum: Z-Uno
- Topic: Color Switch in Z-uno for RGB leds
- Replies: 4
- Views: 4599
Color Switch in Z-uno for RGB leds
Hi, I'm trying to control some RBG leds with Z-uno. I used the ZUNO_SWITCH_COLOR() macro to set-up the channel as in the Reference page. In the controller (Razberry) the color switch is registered properly and I can select a color there. But when I change the RGB color, the Z-Uno setter function is ...
- 06 Jan 2019 16:03
- Forum: Z-Uno
- Topic: No channels registered when selecting S2 security
- Replies: 4
- Views: 4681
Re: No channels registered when selecting S2 security
So one more question - what is the best way to upgrade Z-way to the beta version?
- 05 Jan 2019 13:04
- Forum: Z-Uno
- Topic: No channels registered when selecting S2 security
- Replies: 4
- Views: 4681
Re: No channels registered when selecting S2 security
Thanks for the explanation. The Z-way webpage mentions that it suports S2 without mentioning that this is valid only for the beta version
- 02 Jan 2019 22:54
- Forum: Z-Uno
- Topic: No channels registered when selecting S2 security
- Replies: 4
- Views: 4681
No channels registered when selecting S2 security
I just bought a Razberry and Z-uno to automate my doorlock. I have an issue that when I set Z-uno in S2 security mode the controller (Razberry) registers the device but without any channels. I did the test with the SimpleBinarySensor exemple without anything connected to Z-uno: - in No Security mode...