Search found 16 matches
- 30 May 2024 18:25
- Forum: Z-Uno
- Topic: [solution] Error sketch upload: "Sketch was compiled for another board revision"
- Replies: 1
- Views: 116
[solution] Error sketch upload: "Sketch was compiled for another board revision"
For testing, I used the default sketch: void setup() { // put your setup code here, to run once: } void loop() { // put your main code here, to run repeatedly: } and firmware board Z-Uno2 version 3.0.12 beta. If the compilation was successful. However, an error appears during sketch upload: Error 0 ...
- 28 May 2024 02:19
- Forum: Z-Uno
- Topic: [solution] Error updating bootloader "it's not ZUNO G2 board connected"
- Replies: 1
- Views: 112
[solution] Error updating bootloader "it's not ZUNO G2 board connected"
The board functions normally. However, when updating the bootlader, the error "it's not ZUNO G2 board connected" and "Can't request board information" appears. Rescue modes do not help. It looks like a broken board but it is a firmware error. I bypassed this error by updating the...
- 17 May 2023 21:09
- Forum: Z-Uno
- Topic: After uploading bootloader beta version, the board flashes red. +next board blocked (all bootloaders upload) identically
- Replies: 8
- Views: 3531
Re: After uploading bootloader beta version, the board flashes red. +next board blocked (all bootloaders upload) identic
That's right - at the moment I don't need to update the firmware, but if in the past I needed to, because it had errors that prevented the functioning of my programs and you corrected them in the next versions of the firmware, I will probably also need to update the firmware in the future. Besides, ...
- 16 May 2023 14:29
- Forum: Z-Uno
- Topic: Where has the support gone?
- Replies: 1
- Views: 1033
Where has the support gone?
7 days ago I asked a question. Will I get an answer to them?
https://forum.z-wave.me/viewtopic.php?p=98118#p98118
Regards
https://forum.z-wave.me/viewtopic.php?p=98118#p98118
Regards
- 09 May 2023 10:14
- Forum: Z-Uno
- Topic: After uploading bootloader beta version, the board flashes red. +next board blocked (all bootloaders upload) identically
- Replies: 8
- Views: 3531
Re: After uploading bootloader beta version, the board flashes red. +next board blocked (all bootloaders upload) identic
Hi, you can only upgrade to the newer version of the bootloader( the build number greater that your current), downgrade starting from version 3.11 is not possible due to the SDK features. The board is working correctly. Best regatds, Alex. I understand that I can't downgrade (to 3.0.10) but why can...
- 05 May 2023 00:01
- Forum: Z-Uno
- Topic: After uploading bootloader beta version, the board flashes red. +next board blocked (all bootloaders upload) identically
- Replies: 8
- Views: 3531
Re: After uploading the bootloader, the board flashes red.
This is normal if there are no sketch loaded. The sketch is erased on bootloader upgrade. Just flash a sketch in your Z-Uno 2 I tried and I can upload a sketch after selecting the Z-Uno2 (beta) board version and it stops blinking red and starts blinking green but... ...I wanted to compare with anot...
- 04 May 2023 10:15
- Forum: Z-Uno
- Topic: After uploading bootloader beta version, the board flashes red. +next board blocked (all bootloaders upload) identically
- Replies: 8
- Views: 3531
Re: After uploading the bootloader, the board flashes red.
On the board there is written: "Z-Uno 2 rev.6"
- 03 May 2023 17:45
- Forum: Z-Uno
- Topic: After uploading bootloader beta version, the board flashes red. +next board blocked (all bootloaders upload) identically
- Replies: 8
- Views: 3531
After uploading bootloader beta version, the board flashes red. +next board blocked (all bootloaders upload) identically
After uploading the bootloader, the board flashes red. I haven't done anything with Z-Uno boards in a long time, so I started by updating the firmware. Unfortunately, an error occurred. 1. I upgraded the IDE from 1.8.19 to 2.1.0 and started the new IDE 2. or 3. I chose the Z-Uno2 board, uploaded the...
- 04 Jun 2022 01:43
- Forum: Z-Uno
- Topic: [solved] ZUNO_REPORTS_HANDLER() for Z-Uno2
- Replies: 7
- Views: 4483
Re: ZUNO_REPORTS_HANDLER() for Z-Uno2
Works great. Thank you, but ;P ... macro:
Not yet in the reference. Include them.
Regards
Code: Select all
// You need the WITH_CC_MULTICHANNEL channel to view multi-channel reports (for devices with multiple endpoints, such as ZUno)
ZUNO_ENABLE(WITH_CC_MULTICHANNEL);
Regards
- 02 Jun 2022 00:44
- Forum: Z-Uno
- Topic: [solved] ZUNO_REPORTS_HANDLER() for Z-Uno2
- Replies: 7
- Views: 4483
Re: ZUNO_REPORTS_HANDLER() for Z-Uno2
Okay, I'll wait for the firmware update. Anyway, I've tried this workaround So far, there is one way to make reports work for you - add a dummy SensorMultilevel channel to the receiving sketch. and still don't have reports. Please correct my code: #include "Arduino.h" #define MY_SERIAL Ser...