Z-Way Version 3.0 - Interview buggy

Official announcements from Z-Wave.Me team. Check this forum to get information about new releases and bug fixes.
Post Reply
andy4zway
Posts: 7
Joined: 27 Aug 2019 22:09

Z-Way Version 3.0 - Interview buggy

Post by andy4zway »

I have Z-Way 3.0 installed. After "Start Inclusion" D-Link DCH-Z110 the interview stops at 94%. AssociationGroupInformation" is missing.

I received the following error message (under Experts Page / Association):
Can not configure associations: groups were not reported by the device. Do interview.

Under "Association" in group 1 and 2, I have each entered (#1) Z-Way. And for control "Update from Device" executed.

The interview popular still stands at 94%. In some cases, I could get through expert commands / AssociationGroupInformation / Group 2 / GetName
we're gonna make it to 100%.

But as soon as a new interview is started it stops at 94% again.

With version 2.3.8 D-Link DCH-Z110 was correctly integrated and the interview was finished with 100%.

User avatar
PoltoS
Posts: 5887
Joined: 26 Jan 2011 19:36

Re: Z-Way Version 3.0 - Interview buggy

Post by PoltoS »

In v3.0.0 Z-Way became stricter in Z-Wave protocol (a certification requirement) and devices with bugs in AssociationGroupInformation appears now as not interviewed.

You can bypass it /JS/Run/zway.devices[XXXX].AssociationGroupInformation.data.intervewDone=true

andy4zway
Posts: 7
Joined: 27 Aug 2019 22:09

Re: Z-Way Version 3.0 - Interview buggy

Post by andy4zway »

That was very helpful. I tried it and the interview is now at 100%. Thank you.

192.x.x.x:8083/JS/Run/zway.devices[6].AssociationGroupInformation.data.interviewDone=true

Output -> true

Interview switches to ->100%

CorC
Posts: 10
Joined: 10 Aug 2017 10:34

Re: Z-Way Version 3.0 - Interview buggy

Post by CorC »

Had a similar issue running away 3.0.4 and including a Qubino Flush2 Relay 6.51.09 SDK and AppVersion 5.1 with connected temp.sensor.

It would interview everything except for AssociationGroupInformation in instance 2 [instance 0, 1 and 3 were successful], being stuck at 97%

I had to use this command:

http://xxx.xxx.xxx.xxx:8083/JS/Run/zway ... wDone=true

williamsgems
Posts: 1
Joined: 10 Jul 2020 08:05
Location: USA

Re: Z-Way Version 3.0 - Interview buggy

Post by williamsgems »

Yeah. While including a Qubino flush2 relay 6.51.09 sdk and AppVersion 5.1 with connected temp.sensor. i stuck at 96% later i have completed, now is at 100%. Thank you

ToddGreenfield
Posts: 5
Joined: 20 Dec 2016 20:32

Re: Z-Way Version 3.0 - Interview buggy

Post by ToddGreenfield »

Looking for a little guidance- I have the same issue with an incomplete interview on a GE motion/switch where the interview stops at 92%. The two remaining command classes are AssociationGroupInformation in instance 1 and 2. I tried running the above commands for both instances as such-
http://192.168.4.200:8083/JS/Run/zway.d ... wDone=true
http://192.168.4.200:8083/JS/Run/zway.d ... wDone=true
and the follow-on page does display "true" as output, however on the expert UI it still shows as an incomplete interview. I tried restarting and no change.

Having the same issue with a Schlage BE469ZP door lock. The interview for PowerLevel and Indicator do not complete.
Thanks-

User avatar
PoltoS
Posts: 5887
Joined: 26 Jan 2011 19:36

Re: Z-Way Version 3.0 - Interview buggy

Post by PoltoS »

interview

ToddGreenfield
Posts: 5
Joined: 20 Dec 2016 20:32

Re: Z-Way Version 3.0 - Interview buggy

Post by ToddGreenfield »

Thank you. It helps with correct spelling! Good catch-

Post Reply