UZB stick updated Firmware before bootloader

[steinis]

Hi

I have just bought a UZB stick and a seperate license. But I pressed the wrong button (Firmware) so now I can't install the bootlader. How can I "downgrade" UZB stick and try again?

thanks for input.

[steinis]

No solution for this?

[SgtBilko]

I think I have the same issue.

Z-Way will not communicate with the UZB. Expert Mode says "Error Handling data from Server". Log file has "Opened device: /dev/ttyAMA0", "Job 0x07 (Get controller info and supported function classes): No ACK received before timeout" and "Notification: critical (z-wave): Cannot start Z-Wave binding: Error: Bad data - communication failed". I havn't printed full log becasue I suspect I have the same problem as Stennis.

I look forward to hearing from you as I bought 2 of the UZB's becuase I thought hte 1st was defective. I have a paid for licence.

SgtBilko

[pz1]

For the UZB1 you need to set /dev/ttyACM0 in the Zwave setup

[SgtBilko]

Thank you pz1. Where do I find "Zwave setup" ?

[steinis]

I don´t think this is the same problem. I can't install the boot loader (Whatever that does:P?) because the firmware is up to date.

And how do you see that you have used your license key?

[pz1]

Thank you pz1. Where do I find "Zwave setup" ?

In the smarthome interface under APPS is the Zwave module configuration

[SgtBilko]

Brilliant... thank you very much for your help, pz1

Problem.....Serial Port to Z-Wave dongle is already set up to /dev/ttyACM0

[SgtBilko]

In case it helps here is extract of log file

[2015-08-17 16:47:24.810] [D] [zway] Opened device: /dev/ttyAMA0
[2015-08-17 16:47:24.811] [D] [zway] Worker thread successfully created
[2015-08-17 16:47:24.813] [D] [zway] Worker thread entry point
[2015-08-17 16:47:24.823] [zway] Adding job: Get controller info and supported function classes
[2015-08-17 16:47:24.823] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2015-08-17 16:47:25.031] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2015-08-17 16:47:25.031] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2015-08-17 16:47:25.235] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2015-08-17 16:47:25.236] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2015-08-17 16:47:25.440] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2015-08-17 16:47:25.440] [W] [zway] Job 0x07 (Get controller info and supported function classes) dropped: too many resends
[2015-08-17 16:47:25.440] [D] [zway] Job 0x07 (Get controller info and supported function classes): fail
[2015-08-17 16:47:25.440] [C] [zway] Get Serial API Capabilities returned zero.
[2015-08-17 16:47:25.441] [zway] Removing job: Get controller info and supported function classes
[2015-08-17 16:47:25.451] [D] [zway] Worker thread exit point
[2015-08-17 16:47:25.452] [D] [zway] Worker thread successfully finished
[2015-08-17 16:47:25.454] [E] [zway] SaveData will not save data since it wasn't loaded. This is to prevent data loss.
[2015-08-17 16:47:25.489] [core] Notification: critical (z-wave): Cannot start Z-Wave binding: Error: Bad data - communication failed

[SgtBilko]

Stennis

You were right I didn't have the same problem (see viewtopic.php?f=3419&t=21791 for my solution).

I am sorry to have hijacked your thread, I hope someone can help you.