Razberry & PI 3 will not work
Posted: 22 Apr 2016 13:06
Hi everybody,
i just (23.03) bought a PI3 and the Razberry daughterboard,
but they will not work together.
I read the forum about pi3 problems up and down, but no solution works for me.
Here is my actual configuration:
1. new formated SD
2. install Noobs 1.9.0 from raspberrypi.org
3. install zwave with wget -q -O - http://razberry.z-wave.me ...
there are two modes of incorrect operation:
1. SmartHome UI - Error / Unable to load data
2. if not (1) then, the inclusion failed
with the error code "inclusion takes a long time ..."
and no device will be detected
and the red led lights permanently.
see attachment files
Is there a damage on the razberry daughterboard or is my setup incorrect ?
Attachment:
cmdline.txt:
dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p7 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
config.txt
dtoverlay=pi3-disable-bt
z-way-server log
[2016-04-21 16:05:01.688] [D] [zway] Opened device: /dev/ttyAMA0
[2016-04-21 16:05:01.688] [D] [zway] Worker thread successfully created
[2016-04-21 16:05:01.688] [D] [zway] Worker thread entry point
[2016-04-21 16:05:01.689] [zway] Adding job: Get controller info and supported function classes
[2016-04-21 16:05:01.698] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2016-04-21 16:05:01.699] [D] [zway] RECEIVED CAN
[2016-04-21 16:05:02.002] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2016-04-21 16:05:02.002] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2016-04-21 16:05:02.003] [D] [zway] RECEIVED CAN
[2016-04-21 16:05:02.305] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2016-04-21 16:05:02.305] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2016-04-21 16:05:02.306] [D] [zway] RECEIVED CAN
[2016-04-21 16:05:02.608] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2016-04-21 16:05:02.608] [W] [zway] Job 0x07 (Get controller info and supported function classes) dropped: too many resends
[2016-04-21 16:05:02.608] [D] [zway] Job 0x07 (Get controller info and supported function classes): fail
[2016-04-21 16:05:02.609] [C] [zway] Get Serial API Capabilities returned zero.
[2016-04-21 16:05:02.609] [zway] Removing job: Get controller info and supported function classes
[2016-04-21 16:05:02.619] [D] [zway] Worker thread exit point
[2016-04-21 16:05:02.619] [D] [zway] Worker thread successfully finished
[2016-04-21 16:05:02.619] [E] [zway] SaveData will not save data since it wasn't loaded. This is to prevent data loss.
[2016-04-21 16:05:02.637] [core] Notification: critical (z-wave): Cannot start Z-Wave binding: Error: Bad data - communication failed
i just (23.03) bought a PI3 and the Razberry daughterboard,
but they will not work together.
I read the forum about pi3 problems up and down, but no solution works for me.
Here is my actual configuration:
1. new formated SD
2. install Noobs 1.9.0 from raspberrypi.org
3. install zwave with wget -q -O - http://razberry.z-wave.me ...
there are two modes of incorrect operation:
1. SmartHome UI - Error / Unable to load data
2. if not (1) then, the inclusion failed
with the error code "inclusion takes a long time ..."
and no device will be detected
and the red led lights permanently.
see attachment files
Is there a damage on the razberry daughterboard or is my setup incorrect ?
Attachment:
cmdline.txt:
dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p7 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
config.txt
dtoverlay=pi3-disable-bt
z-way-server log
[2016-04-21 16:05:01.688] [D] [zway] Opened device: /dev/ttyAMA0
[2016-04-21 16:05:01.688] [D] [zway] Worker thread successfully created
[2016-04-21 16:05:01.688] [D] [zway] Worker thread entry point
[2016-04-21 16:05:01.689] [zway] Adding job: Get controller info and supported function classes
[2016-04-21 16:05:01.698] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2016-04-21 16:05:01.699] [D] [zway] RECEIVED CAN
[2016-04-21 16:05:02.002] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2016-04-21 16:05:02.002] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2016-04-21 16:05:02.003] [D] [zway] RECEIVED CAN
[2016-04-21 16:05:02.305] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2016-04-21 16:05:02.305] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2016-04-21 16:05:02.306] [D] [zway] RECEIVED CAN
[2016-04-21 16:05:02.608] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2016-04-21 16:05:02.608] [W] [zway] Job 0x07 (Get controller info and supported function classes) dropped: too many resends
[2016-04-21 16:05:02.608] [D] [zway] Job 0x07 (Get controller info and supported function classes): fail
[2016-04-21 16:05:02.609] [C] [zway] Get Serial API Capabilities returned zero.
[2016-04-21 16:05:02.609] [zway] Removing job: Get controller info and supported function classes
[2016-04-21 16:05:02.619] [D] [zway] Worker thread exit point
[2016-04-21 16:05:02.619] [D] [zway] Worker thread successfully finished
[2016-04-21 16:05:02.619] [E] [zway] SaveData will not save data since it wasn't loaded. This is to prevent data loss.
[2016-04-21 16:05:02.637] [core] Notification: critical (z-wave): Cannot start Z-Wave binding: Error: Bad data - communication failed