HomeSettings HA05 - Screw-in Module

[brent192]

I'm having trouble getting this device to include... It sees it come up but never adds it in the system. I see a failed message in the Inspect Queue, but no error message in the log file. Any ideas?

[2013-09-25 23:20:12.056] Executing script: zway.controller.AddNodeToNetwork(1)
[2013-09-25 23:20:12.057] Adding job: Add/re-include node to network
[2013-09-25 23:20:12.064] SENDING (cb 0xbb): ( 01 05 00 4A C1 BB CA )
[2013-09-25 23:20:12.076] RECEIVED ACK
[2013-09-25 23:20:12.087] RECEIVED: ( 01 07 00 4A BB 01 00 00 08 )
[2013-09-25 23:20:12.088] SENT ACK
[2013-09-25 23:20:12.089] SETDATA controller.data.lastIncludedDevice = Empty
[2013-09-25 23:20:12.091] SETDATA controller.data.lastExcludedDevice = Empty
[2013-09-25 23:20:12.092] Job 0x4a (Add/re-include node to network): Ready to add - push button on the device to be added
[2013-09-25 23:20:12.093] SETDATA controller.data.controllerState = 1 (0x00000001)
[2013-09-25 23:20:12.648] Executing script: zway.InspectQueue()
[2013-09-25 23:20:13.646] Executing script: zway.InspectQueue()
[2013-09-25 23:20:14.647] Executing script: zway.InspectQueue()
[2013-09-25 23:20:15.647] Executing script: zway.InspectQueue()
[2013-09-25 23:20:15.935] RECEIVED: ( 01 07 00 4A BB 02 00 00 0B )
[2013-09-25 23:20:15.936] SENT ACK
[2013-09-25 23:20:15.937] Job 0x4a (Add/re-include node to network): Node found: #0
[2013-09-25 23:20:15.939] SETDATA controller.data.controllerState = 2 (0x00000002)
[2013-09-25 23:20:16.648] Executing script: zway.InspectQueue()
[2013-09-25 23:20:17.658] Executing script: zway.InspectQueue()
[2013-09-25 23:20:18.647] Executing script: zway.InspectQueue()
[2013-09-25 23:20:19.052] RECEIVED: ( 01 07 00 4A BB 07 00 00 0E )
[2013-09-25 23:20:19.053] SENT ACK
[2013-09-25 23:20:19.054] Job 0x4a (Add/re-include node to network): Failed
[2013-09-25 23:20:19.056] Job 0x4a (Add/re-include node to network): fail
[2013-09-25 23:20:19.056] Removing job: Add/re-include node to network
[2013-09-25 23:20:19.058] Adding job: Add/re-include node to network
[2013-09-25 23:20:19.070] SENDING (cb 0xc5): ( 01 04 00 4A C5 74 )
[2013-09-25 23:20:19.082] RECEIVED ACK
[2013-09-25 23:20:19.083] Removing job: Add/re-include node to network
[2013-09-25 23:20:19.128] RECEIVED: ( 01 07 00 4A BB 06 00 00 0F )
[2013-09-25 23:20:19.129] SENT ACK
[2013-09-25 23:20:19.130] Job 0x4a (Add/re-include node to network): Done
[2013-09-25 23:20:19.131] SETDATA controller.data.controllerState = 0 (0x00000000)
[2013-09-25 23:20:19.132] Job 0x4a (Add/re-include node to network): success
[2013-09-25 23:20:19.133] Removing job: Add/re-include node to network

[PoltoS]

You certainly press NIF button sequence instead of learn mode sequence. Please read user manual of your device to check button sequence you nee to include the device.