How to configure JP frequency on ZMEARAZ2

Discussions about RaZberry - Z-Wave board for Raspberry computer
Post Reply
nztak
Posts: 5
Joined: 04 Jan 2021 15:02

How to configure JP frequency on ZMEARAZ2

Post by nztak »

Dear Z-Wave.Me,

I can't set it to JP frequency in the expert interface on ZMEARAZ2.
Could you tell me how to configure JP frequency?


[Detail]
- model: ZMEARAZ2 of RaZberry (Version for all frequencies around 921 MHz (Australia/Brasil, Japan, Korea))
- SDK version : 6.51.06
- change frequency: http://ZWAYIP:8083/JS/Run/zway.ZMEFreqChange(4)
-> ANZ/BR HK only appeared. NOT KR/JP.
-> try http://ZWAYIP:8083/JS/Run/zway.ZMEFreqChange(7) -> KR/JP appeard!!
-> exclusion -> inclusion -> cannot find JP device.

- Below is a copy paste from http://ZWAYIP:8083/expert/#/network/controller "Show Controller Data"

Code: Select all


/: None (03.01.2021)
    nodeId: 1 (03.01.2021)
    homeId: 1431655765 (03.01.2021)
    SUCNodeId: 0 (03.01.2021)
    isPrimary: true (03.01.2021)
    isInOthersNetwork: false (03.01.2021)
    isRealPrimary: false (03.01.2021)
    isSUC: false (03.01.2021)
    SISPresent: false (03.01.2021)
    libType: Static Controller (03.01.2021)
    SDK: 6.51.06 (03.01.2021)
    ZWlibMajor: 4 (03.01.2021)
    ZWlibMinor: 5 (03.01.2021)
    ZWLib: 1 (03.01.2021)
    ZWVersion: 5 (03.01.2021)
    ZWaveChip: ZW0500 (03.01.2021)
    APIVersion: 05.04 (03.01.2021)
    APIVersionMajor: 5 (03.01.2021)
    APIVersionMinor: 4 (03.01.2021)
    manufacturerId: 327 (03.01.2021)
    vendor: RaZberry by Z-Wave.Me (03.01.2021)
    manufacturerProductType: 1024 (03.01.2021)
    manufacturerProductId: 2 (03.01.2021)
    bootloaderCRC: 48059 (03.01.2021)
    firmwareCRC: 21090 (03.01.2021)
    capabilities: 2,3,4,5,6,7,8,9,10,16,17,18,19,20,21,22,23,24,28,32,33,34,35,36,39,40,41,42,43,44,45,65,66,68,69,70,71,72,73,74,75,76,77,80,81,83,84,85,86,87,94,96,97,98,99,102,103,120,128,144,146,147,152,180,182,183,184,185,186,189,190,191,210,211,212,239,242,244,245 (03.01.2021)
    controllerState: 0 (03.01.2021)
    nonManagmentJobs: 0 (03.01.2021)
    lastIncludedDevice: 0 (03.01.2021)
    lastExcludedDevice: 0 (03.01.2021)
    secureInclusion: true (03.01.2021)
    oldSerialAPIAckTimeout10ms: 150 (03.01.2021)
    oldSerialAPIByteTimeout10ms: 15 (03.01.2021)
    curSerialAPIAckTimeout10ms: 10 (03.01.2021)
    curSerialAPIByteTimeout10ms: 10 (03.01.2021)
    countJobs: false (03.01.2021)
    memoryGetAddress: 32768 (03.01.2021)
    memoryGetData: 131,31,164,161,72,183,118,67,239,102,95,44,10,210,229,138,118,156,105,115,96,187,199,161,87,22,42,63,202,190,29,185,101,22,159,24,245,59,155,35,108,210,27,176,110,176,97,136,71,14,160,97,154,246,231,198,98,58,67,183,2,123,66,32 (03.01.2021)
    memoryManufacturerId: None (03.01.2021)
    memoryType: None (03.01.2021)
    memoryCapacity: None (03.01.2021)
    functionClasses: 2,3,4,5,6,7,8,11,18,19,21,22,23,32,33,34,35,36,39,41,42,43,44,45,57,58,59,63,65,66,68,70,71,72,73,74,75,76,77,79,80,81,82,83,84,85,86,87,88,94,96,97,98,99,128,146,147,186,190,208,209,210,211,242,243,244,245,248 (03.01.2021)
    functionClassesNames: SerialAPIGetInitData,SerialAPIApplicationNodeInformation,ApplicationCommandHandler,GetControllerCapabilities,SerialAPISetTimeouts,GetSerialAPICapabilities,SerialAPISoftReset,SerialAPISetup,SendNodeInformation,SendData,GetVersion,SendDataAbort,RFPowerLevelSet,GetHomeId,MemoryGetByte,MemoryPutByte,MemoryGetBuffer,MemoryPutBuffer,FlashAutoProgSet,NVMGetId,NVMExtReadLongBuffer,NVMExtWriteLongBuffer,NVMExtReadLongByte,NVMExtWriteLongByte,ClearNetworkStats,GetNetworkStats,GetBackgroundRSSI,RemoveNodeIdFromNetwork,GetNodeProtocolInformation,SetDefault,ReplicationReceiveComplete,AssignReturnRoute,DeleteReturnRoute,RequestNodeNeighbourUpdate,ApplicationNodeUpdate,AddNodeToNetwork,RemoveNodeFromNetwork,CreateNewPrimary,ControllerChange,AssignPriorityReturnRoute,SetLearnMode,AssignSUCReturnRoute,EnableSUC,RequestNetworkUpdate,SetSUCNodeId,DeleteSUCReturnRoute,GetSUCNodeId,SendSUCNodeId,AssignPrioritySUC ReturnRoute,ExploreRequestInclusion,RequestNodeInformation,RemoveFailedNode,IsFailedNode,ReplaceFailedNode,GetRoutingTableLine,GetPriorityRoute,SetPriorityRoute,RFPowerLevelGet,SendTestFrame,SetPromiscuousMode,PromiscuousCommandHandler,WatchDogStart,WatchDogStop,ZMEFreqChange,ZMERestore,ZMEBootloaderFlash,ZMECapabilities,ZMESerialAPIOptions (03.01.2021)
    softwareRevisionVersion: v3.1.1 (03.01.2021)
    softwareRevisionId: 0b66875dc97ac195481bb216ffd26067e67735e2 (03.01.2021)
    softwareRevisionDate: 2020-09-16 02:22:09 +0300 (03.01.2021)
    uuid: 7c4e98470073f2b0ca08f52113c588b0 (03.01.2021)
    caps: 0,0,255,5 (03.01.2021)
    capsNonce: 0,0,0,0 (03.01.2021)
    countDown: 0 (03.01.2021)
    frequency: JP (03.01.2021)
    deviceRelaxDelay: 3 (03.01.2021)
    promiscMode: false (03.01.2021)
    statistics: None (03.01.2021)
        backgroundRSSI: None (03.01.2021)
            channel1: 127 (03.01.2021)
            channel2: 127 (03.01.2021)
            channel3: 127 (03.01.2021)
        RFTxFrames: 0 (03.01.2021)
        RFTxLBTBackOffs: 0 (03.01.2021)
        RFRxFrames: 0 (03.01.2021)
        RFRxLRCErrors: 0 (03.01.2021)
        RFRxCRC16Errors: 0 (03.01.2021)
        RFRxForeignHomeID: 0 (03.01.2021)
        priorityRoute: None (03.01.2021)
            dstNodeId: None (03.01.2021)
            routeType: None (03.01.2021)
            speed: None (03.01.2021)
            hops: None (03.01.2021)
        jammingDetection: None (03.01.2021)
            ch1Threshold: 127 (03.01.2021)
            ch2Threshold: 127 (03.01.2021)
            ch3Threshold: 127 (03.01.2021)
            detected: 0 (03.01.2021)
    homeName: (27.12.2020)
    homeNotes: (27.12.2020)
    S2RequireCSA: false (03.01.2021)
    smartStart: None (27.12.2020)
        requestFrom: None (03.01.2021)
        dskProvisioningList: None (27.12.2020)
        includingDSK: None (03.01.2021)
- /var/log/z-way-server.log -> Attached

[Reference]
I already checked folowing topics.
- https://forum.z-wave.me/viewtopic.php?t=23417
- https://forum.z-wave.me/viewtopic.php?t=25491
- https://forum.z-wave.me/viewtopic.php?t=25882
Attachments
var-logz-way-serverlog.zip
/var/log/z-way-server.log
(277.83 KiB) Downloaded 5 times
User avatar
PoltoS
Posts: 6106
Joined: 26 Jan 2011 19:36

Re: How to configure JP frequency on ZMEARAZ2

Post by PoltoS »

You need to go in firmware upgrade and install 3 channels firmware. It is a special one for KR/JP. Please got on /expert/#/uzb and anter token "all". You will see proposals to upgrade the bootloader and firmware. Please follow up to 5.39. You will see 3 channels (JP) version there.
nztak
Posts: 5
Joined: 04 Jan 2021 15:02

Re: How to configure JP frequency on ZMEARAZ2

Post by nztak »

Thanks for prompt reply.
I try to upgrade firmware 5.4->5.7. Then it says latest firmware as attached file.
But I can't succeed inclusion.
( I tried factory reset or ZMEFreqChange(4) or ZMEFreqChange(7) )
Have you ever heard of this situation?


By the way, I don't find my firmware version.
I'd like to check my firmware version is Ver5.39 or not.
Where can I get firmware version?

Thanks.
Attachments
Screen capture for
Screen capture for
firmware_update_done.jpg (108.03 KiB) Viewed 171 times
User avatar
PoltoS
Posts: 6106
Joined: 26 Jan 2011 19:36

Re: How to configure JP frequency on ZMEARAZ2

Post by PoltoS »

Please check on the Contoller Info page your current version. You should be able to upgrade 5.7->5.23->5.32->...
nztak
Posts: 5
Joined: 04 Jan 2021 15:02

Re: How to configure JP frequency on ZMEARAZ2

Post by nztak »

Thanks for prompt reply.

I serched Contoller Info page.
But I can't find which version you said as follows:
- SDK Version:
- Serial API Version:
- Version number
- UI version

Code: Select all

Role in Network
Node Id:	1
Home Id:	0x55555555
Primary Role:	Yes
Primary Capability:	Yes
SUC/SIS in network:	1 (SIS)
Hardware
Vendor:	RaZberry by Z-Wave.Me
Vendors Product ID:	1024 / 2
Z-Wave Chip:	ZW0500
Firmware
Library Type:	Static Controller
SDK Version:	6.71.01
Serial API Version:	05.22
Capabillities:
UUID:	00000000000000000000000000000000
Subvendor:	0x0000
Nodes limit:	00
Capabillities:	slm
Software Information
Version number:	v3.1.1
Compile-ID:	0b66875dc97ac195481bb216ffd26067e67735e2
Compile-Date:	2020-09-16 02:22:09 +0300
UI
UI version	1.5.2
Built date	31-08-2020 01:20:08
Thanks,
nztak
Posts: 5
Joined: 04 Jan 2021 15:02

Re: How to configure JP frequency on ZMEARAZ2

Post by nztak »

It seems I got Ver5.39 firmware. Thanks!!

- It seems APIVersion is firmware version.
- firmware update -> "Your stick uses the lateset firmware" display -> logout -> login again -> we can find new next firmware version -> firmware update.

Code: Select all

/: None (22:38)
    nodeId: 1 (22:38)
    homeId: 1431655765 (22:38)
    SUCNodeId: 1 (22:38)
    isPrimary: true (22:39)
    isInOthersNetwork: false (22:39)
    isRealPrimary: true (22:39)
    isSUC: true (22:39)
    SISPresent: true (22:39)
    libType: Static Controller (22:38)
    SDK: 6.82.01 (22:38)
    ZWlibMajor: 6 (22:38)
    ZWlibMinor: 9 (22:38)
    ZWLib: 1 (22:38)
    ZWVersion: 6 (22:38)
    ZWaveChip: ZW0500 (22:38)
    APIVersion: 05.39 (22:38)
    APIVersionMajor: 5 (22:38)
    APIVersionMinor: 39 (22:38)
    manufacturerId: 327 (22:38)
    vendor: RaZberry by Z-Wave.Me (22:38)
    manufacturerProductType: 1024 (22:38)
    manufacturerProductId: 2 (22:38)
    bootloaderCRC: 35498 (22:39)
    firmwareCRC: 25539 (22:39)
    capabilities: 2,3,4,5,6,7,8,9,10,11,16,17,18,19,20,21,22,23,28,32,33,34,35,36,39,40,41,42,43,44,45,46,55,56,57,58,59,63,65,66,68,69,70,71,72,73,74,75,76,77,79,80,81,83,84,85,86,87,88,94,95,96,97,98,99,102,103,120,128,144,146,147,152,180,182,183,184,185,186,189,190,191,208,209,210,211,212,238,239,242,244,245,247,248 (22:38)
    controllerState: 0 (22:39)
    nonManagmentJobs: 0 (22:38)
    lastIncludedDevice: 0 (22:38)
    lastExcludedDevice: 0 (22:38)
    secureInclusion: true (22:38)
    oldSerialAPIAckTimeout10ms: 150 (22:38)
    oldSerialAPIByteTimeout10ms: 15 (22:38)
    curSerialAPIAckTimeout10ms: 10 (22:38)
    curSerialAPIByteTimeout10ms: 10 (22:38)
    countJobs: false (22:38)
    memoryGetAddress: 32768 (22:39)
    memoryGetData: 154,24,101,190,159,6,35,72,238,204,27,237,8,0,16,188,32,18,60,158,26,179,20,204,231,176,86,175,242,81,223,15,9,143,71,255,199,75,75,159,25,46,176,253,26,44,178,132,237,240,169,166,27,103,33,44,97,65,44,177,196,69,82,44 (22:39)
    memoryManufacturerId: None (22:38)
    memoryType: None (22:38)
    memoryCapacity: None (22:38)
    functionClasses: 2,3,4,5,6,7,8,11,18,19,21,22,23,32,33,34,35,36,39,41,42,43,44,45,57,58,59,63,65,66,68,70,71,72,73,74,75,76,77,79,80,81,82,83,84,85,86,87,88,94,96,97,98,99,128,146,147,186,190,208,209,210,211,242,243,244,245,248 (22:38)
    functionClassesNames: SerialAPIGetInitData,SerialAPIApplicationNodeInformation,ApplicationCommandHandler,GetControllerCapabilities,SerialAPISetTimeouts,GetSerialAPICapabilities,SerialAPISoftReset,SerialAPISetup,SendNodeInformation,SendData,GetVersion,SendDataAbort,RFPowerLevelSet,GetHomeId,MemoryGetByte,MemoryPutByte,MemoryGetBuffer,MemoryPutBuffer,FlashAutoProgSet,NVMGetId,NVMExtReadLongBuffer,NVMExtWriteLongBuffer,NVMExtReadLongByte,NVMExtWriteLongByte,ClearNetworkStats,GetNetworkStats,GetBackgroundRSSI,RemoveNodeIdFromNetwork,GetNodeProtocolInformation,SetDefault,ReplicationReceiveComplete,AssignReturnRoute,DeleteReturnRoute,RequestNodeNeighbourUpdate,ApplicationNodeUpdate,AddNodeToNetwork,RemoveNodeFromNetwork,CreateNewPrimary,ControllerChange,AssignPriorityReturnRoute,SetLearnMode,AssignSUCReturnRoute,EnableSUC,RequestNetworkUpdate,SetSUCNodeId,DeleteSUCReturnRoute,GetSUCNodeId,SendSUCNodeId,AssignPrioritySUC ReturnRoute,ExploreRequestInclusion,RequestNodeInformation,RemoveFailedNode,IsFailedNode,ReplaceFailedNode,GetRoutingTableLine,GetPriorityRoute,SetPriorityRoute,RFPowerLevelGet,SendTestFrame,SetPromiscuousMode,PromiscuousCommandHandler,WatchDogStart,WatchDogStop,ZMEFreqChange,ZMERestore,ZMEBootloaderFlash,ZMECapabilities,ZMESerialAPIOptions (22:38)
    softwareRevisionVersion: v3.1.1 (22:38)
    softwareRevisionId: 0b66875dc97ac195481bb216ffd26067e67735e2 (22:38)
    softwareRevisionDate: 2020-09-16 02:22:09 +0300 (22:38)
    uuid: 7c4e98470073f2b0ca08f52113c588b0 (22:38)
    caps: 0,0,255,5 (22:38)
    capsNonce: 0,0,0,0 (22:38)
    countDown: 0 (22:38)
    frequency: JP (22:41)
    deviceRelaxDelay: 3 (22:38)
    promiscMode: false (22:38)
    statistics: None (22:38)
        backgroundRSSI: None (22:38)
            channel1: 179 (22:42)
            channel2: 182 (22:42)
            channel3: 179 (22:42)
        RFTxFrames: 1 (22:39)
        RFTxLBTBackOffs: 0 (22:39)
        RFRxFrames: 0 (22:39)
        RFRxLRCErrors: 0 (22:39)
        RFRxCRC16Errors: 0 (22:39)
        RFRxForeignHomeID: 0 (22:39)
        priorityRoute: None (22:38)
            dstNodeId: None (22:38)
            routeType: None (22:38)
            speed: None (22:38)
            hops: None (22:38)
        jammingDetection: None (22:38)
            ch1Threshold: 127 (22:38)
            ch2Threshold: 127 (22:38)
            ch3Threshold: 127 (22:38)
            detected: 0 (22:38)
    homeName: (27.12.2020)
    homeNotes: (27.12.2020)
    S2RequireCSA: false (22:38)
    smartStart: None (27.12.2020)
        requestFrom: None (22:38)
        dskProvisioningList: None (27.12.2020)
        includingDSK: None (22:38)

But I haven't succeed inclusion yet.
It seems to finish inclusion one part, Razberry LED flash stop and Z-Wave sensor inclusion LED flashing stop.
But inclusion console continue inclusion mode, "Ready to include".
( http://ZWAYIP:8083/smarthome/#zwave/inclusion )
Does anybody know this solution?

Thanks,
Attachments
frequency_jp_ver5-39.JPG
frequency_jp_ver5-39.JPG (20.06 KiB) Viewed 132 times
User avatar
PoltoS
Posts: 6106
Joined: 26 Jan 2011 19:36

Re: How to configure JP frequency on ZMEARAZ2

Post by PoltoS »

For JP and KR you need 3 channels firmware. 5.36 had that as I remember. May be 5.39 do have it too - need to check that.
nztak
Posts: 5
Joined: 04 Jan 2021 15:02

Re: How to configure JP frequency on ZMEARAZ2

Post by nztak »

Ver5.39 JP/TW/KR firmware works as follows:

- http://ZWAYIP:8083/smarthome/#/zwave/inclusion
-> include FAIL. Razberry LED flash stop and Z-Wave sensor inclusion LED flashing stop. But "Ready to include".continue.

- http://ZWAYIP:8083/expert/#/network/control
-> inclusion partially success. S2 interview doesn't complete.


I think this remain issue is not JP frequency issue.
So I close this ticket.

Thanks a lot!!
Attachments
S2 interview is NOT complete.
S2 interview is NOT complete.
razberry_expert_inclusion2.JPG (56.77 KiB) Viewed 92 times
expert force inclusion
expert force inclusion
razberry_expert_inclusion1.JPG (30.25 KiB) Viewed 92 times
Post Reply