List of bugs
Posted: 09 Jun 2013 18:28
Hi,
I´m currently encountering the following bugs with my Razberry installation:
- The Meter interview does not finish for any of my ~15 Everspring AN158 Switches with Metering function.
Re-including them or forcing the interview manually does not do anything. This behaviour is the same for every single one of them. They do support the METER_V2 command class.
This is the log file for the Force Re-interview of the Meter class:
[2013-06-09 15:47:04.534] Adding job: Meter supported get
[2013-06-09 15:47:04.536] SENDING (cb 0x96): ( 01 09 00 13 05 02 32 03 25 96 60 )
[2013-06-09 15:47:04.566] RECEIVED ACK
[2013-06-09 15:47:04.578] RECEIVED: ( 01 04 01 13 01 E8 )
[2013-06-09 15:47:04.587] SENT ACK
[2013-06-09 15:47:04.589] Delivered to Z-Wave stack
[2013-06-09 15:47:04.683] RECEIVED: ( 01 05 00 13 96 00 7F )
[2013-06-09 15:47:04.694] SENT ACK
[2013-06-09 15:47:04.696] Job 0x13 (Meter supported get): Delivered
[2013-06-09 15:47:04.698] SendData Response with callback 0x96 received: received by recipient
[2013-06-09 15:47:04.700] SETDATA devices.5.data.lastSend = 56690335 (0x0361069f)
[2013-06-09 15:47:04.702] Job 0x13 (Meter supported get): success
[2013-06-09 15:47:04.704] Removing job: Meter supported get
- I have two Aeon Labs Multisensors, both are detected as "Multi Sensor 1.18". After including them, they show up as sensors for Humidity,Temperature,Luminiscence and "State" (=motion detected). These values are all that they support. After a few days, new random sensors show up magically like "Generic", "Power" etc. This is very annoying as the values mix up with the "real" existing values and the readings are useless.
- Sometimes, lights do magically switch on and off e.g. at night.
- Configuration values from devices seem to be wandering across devices, e.g. if I read the configuration from all devices the configuration values do not seem to be associated to the correct device and show up at another one. This happens randomly.
I suspect that the whole queue management / data management is a bit messed up in Razberry and that this might be causing the effects I´m experiencing.
Unfortunately Razberry is not open software so I´m unable to fix this myself.
What can I do to get this right ? My installation is unusable at this point. I did already clean the network and start with a fresh installation, however this did not help.
Regards,
Nicholas
I´m currently encountering the following bugs with my Razberry installation:
- The Meter interview does not finish for any of my ~15 Everspring AN158 Switches with Metering function.
Re-including them or forcing the interview manually does not do anything. This behaviour is the same for every single one of them. They do support the METER_V2 command class.
This is the log file for the Force Re-interview of the Meter class:
[2013-06-09 15:47:04.534] Adding job: Meter supported get
[2013-06-09 15:47:04.536] SENDING (cb 0x96): ( 01 09 00 13 05 02 32 03 25 96 60 )
[2013-06-09 15:47:04.566] RECEIVED ACK
[2013-06-09 15:47:04.578] RECEIVED: ( 01 04 01 13 01 E8 )
[2013-06-09 15:47:04.587] SENT ACK
[2013-06-09 15:47:04.589] Delivered to Z-Wave stack
[2013-06-09 15:47:04.683] RECEIVED: ( 01 05 00 13 96 00 7F )
[2013-06-09 15:47:04.694] SENT ACK
[2013-06-09 15:47:04.696] Job 0x13 (Meter supported get): Delivered
[2013-06-09 15:47:04.698] SendData Response with callback 0x96 received: received by recipient
[2013-06-09 15:47:04.700] SETDATA devices.5.data.lastSend = 56690335 (0x0361069f)
[2013-06-09 15:47:04.702] Job 0x13 (Meter supported get): success
[2013-06-09 15:47:04.704] Removing job: Meter supported get
- I have two Aeon Labs Multisensors, both are detected as "Multi Sensor 1.18". After including them, they show up as sensors for Humidity,Temperature,Luminiscence and "State" (=motion detected). These values are all that they support. After a few days, new random sensors show up magically like "Generic", "Power" etc. This is very annoying as the values mix up with the "real" existing values and the readings are useless.
- Sometimes, lights do magically switch on and off e.g. at night.
- Configuration values from devices seem to be wandering across devices, e.g. if I read the configuration from all devices the configuration values do not seem to be associated to the correct device and show up at another one. This happens randomly.
I suspect that the whole queue management / data management is a bit messed up in Razberry and that this might be causing the effects I´m experiencing.
Unfortunately Razberry is not open software so I´m unable to fix this myself.
What can I do to get this right ? My installation is unusable at this point. I did already clean the network and start with a fresh installation, however this did not help.
Regards,
Nicholas