Failing FW update from 5.00

Discussions about RaZberry - Z-Wave board for Raspberry computer
Post Reply
nikitin
Posts: 3
Joined: 02 Dec 2020 16:46

Failing FW update from 5.00

Post by nikitin »

I've been trying to read up on FW upgrading, I've downloaded the ZMESerialUpdater tool and read the instructions.

I first ran

Code: Select all

root@raspberrypi:~/ZMESerialUpdater/arm# ./ZMESerialUpdater serialapi_uzbupdate -d /dev/ttyAMA0 | grep -E "(FREQ|VERSION)"
           VERSION:  05 00  VENDOR:  01 47
              FREQ:  N/A 
Next i ran

Code: Select all

root@raspberrypi:~/ZMESerialUpdater/arm# ./ZMESerialUpdater serialapi_uzbupdate -d /dev/ttyAMA0


                         Z-WAVE Serial API Tool
                              Version:LWE0.9
                              by Z-WAVE>ME


-->
Device ready in:3.05745911598 seconds
          FULL INFO
Openning port                            ..............................                            OK


          SERIAL INFO 
           VERSION:  05 00  VENDOR:  01 47

          ZME_CAPABILITIES 
               UID:  03 E6 EC 0C EA 1C 5C A1 52 53 2E 2F 79 E9 94 99 
            VENDOR:  00 00   NODES: FF 
             FLAGS:  01 00 00 00 00 00 00 00 00 00 00 00 00

          FIRMWARE CRC
              BOOT:  FF FF      FW:  FF FF
          MISC 
              FREQ:  N/A 
           
                               NVR Content
          -------------------------------------------------------------------------------------------- 
          Prog/erase lock :  FF FF FF FF FF FF FF FF, Read back lock: FF
          Rev FF, Cal FF, TXCal  FF FF, SAW  FF FF FF FF, Pin FF, CRC  FF FF
          NMV: CS FF, TYPE FF, SIZE  FF FF, PSIZE  FF FF (EEPROM Unknown)
          USB: VID  FF FF, PID  FF FF, UUID  FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          -------------------------------------------------------------------------------------------- 
          FACTORY ID: WEEK 255, YEAR 255, CHIP  FF FF, SER  FF FF, WS 255, HWREV: FF FF, CRC8 FF
           
          elapsed 5.25775980949 seconds
And finally

Code: Select all

root@raspberrypi:~/ZMESerialUpdater/arm# ./ZMESerialUpdater serialapi_uzbupdate -d /dev/ttyAMA0 -b bootloader_Razberry_from_05_00_to_538d.bin -f firmware_Razberry_from_05_00_to_05_04.bin 


                                        Z-WAVE Serial API Tool
                                             Version:LWE0.9
                                             by Z-WAVE>ME


-->
Device ready in:3.06612896919 seconds
          BOOTLODER
Openning port                            ..............................                            OK
Writing NVM data                         ..............................                            OK
Waiting for Boot reflashing              ..............................                            OK
-->
Device ready in:1.04261088371 seconds
          FIRMWARE
Openning port                            ..............................                            OK
Writing NVM data                         ..............................                            OK
Setting update flag                      ..............................                            OK
Reseting chip                            ..............................                            OK
Waiting for FW reflashing                ..............................                            OK
-->
Device ready in:1.0419280529 seconds
          FULL INFO
Openning port                            ..............................                            OK


          SERIAL INFO 
                 VERSION:  05 00  VENDOR:  01 47

          ZME_CAPABILITIES 
                     UID:  03 E6 EC 0C EA 1C 5C A1 52 53 2E 2F 79 E9 94 99 
                  VENDOR:  00 00   NODES: FF 
                   FLAGS:  01 00 00 00 00 00 00 00 00 00 00 00 00

          FIRMWARE CRC
                    BOOT:  FF FF      FW:  FF FF
          MISC 
                    FREQ:  N/A 
           
                                         NVR Content
          -------------------------------------------------------------------------------------------- 
          Prog/erase lock :  FF FF FF FF FF FF FF FF, Read back lock: FF
          Rev FF, Cal FF, TXCal  FF FF, SAW  FF FF FF FF, Pin FF, CRC  FF FF
          NMV: CS FF, TYPE FF, SIZE  FF FF, PSIZE  FF FF (EEPROM Unknown)
          USB: VID  FF FF, PID  FF FF, UUID  FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          -------------------------------------------------------------------------------------------- 
          FACTORY ID: WEEK 255, YEAR 255, CHIP  FF FF, SER  FF FF, WS 255, HWREV: FF FF, CRC8 FF
           
          elapsed 85.2651219368 seconds
Next time I check it still shows FW version 5.00.

Any ideas on what I'm doing wrong?
User avatar
PoltoS
Posts: 6086
Joined: 26 Jan 2011 19:36

Re: Failing FW update from 5.00

Post by PoltoS »

5.00 is the very first firmware on 5 gen. It is hard to upgrade. Easiest is to bring it to our office
nikitin
Posts: 3
Joined: 02 Dec 2020 16:46

Re: Failing FW update from 5.00

Post by nikitin »

PoltoS wrote:
03 Dec 2020 10:15
5.00 is the very first firmware on 5 gen. It is hard to upgrade. Easiest is to bring it to our office
Alright, I haven't updated the firmware since I got the RazBerry.
Would there be any way for you to do this remotely? Or would I need to mail in the board to you?
nikitin
Posts: 3
Joined: 02 Dec 2020 16:46

Re: Failing FW update from 5.00

Post by nikitin »

@PoltoS pinging up this thread, any chance you could help me out?
User avatar
PoltoS
Posts: 6086
Joined: 26 Jan 2011 19:36

Re: Failing FW update from 5.00

Post by PoltoS »

Please write to support@, they will guide you.
Post Reply