After uploading bootloader beta version, the board flashes red. +next board blocked (all bootloaders upload) identically
Posted: 03 May 2023 17:45
After uploading the bootloader, the board flashes red.
I haven't done anything with Z-Uno boards in a long time, so I started by updating the firmware. Unfortunately, an error occurred.
1. I upgraded the IDE from 1.8.19 to 2.1.0 and started the new IDE
2. or 3. I chose the Z-Uno2 board, uploaded the bootloader, then a simple sketch - everything OK
2. or 3. I chose the Z-Uno2 Beta board, uploaded the bootloader, then a simple sketch - everything OK
3. I updated the Z-Uno2 board software, uploaded the bootloader, then a simple sketch - everything OK
4. An error occurred while updating the Z-Uno2 Beta board. I removed the Z-Uno Beta board software and reinstalled it, uploaded the bootloader and an error appeared, and the board started blinking red and restarting every few dozen seconds.
When trying to upload the bootloader, this error is shown (or the board restarts earlier and then shows a memory error).
Is my z-uno board damaged?
I haven't done anything with Z-Uno boards in a long time, so I started by updating the firmware. Unfortunately, an error occurred.
1. I upgraded the IDE from 1.8.19 to 2.1.0 and started the new IDE
2. or 3. I chose the Z-Uno2 board, uploaded the bootloader, then a simple sketch - everything OK
2. or 3. I chose the Z-Uno2 Beta board, uploaded the bootloader, then a simple sketch - everything OK
3. I updated the Z-Uno2 board software, uploaded the bootloader, then a simple sketch - everything OK
4. An error occurred while updating the Z-Uno2 Beta board. I removed the Z-Uno Beta board software and reinstalled it, uploaded the bootloader and an error appeared, and the board started blinking red and restarting every few dozen seconds.
When trying to upload the bootloader, this error is shown (or the board restarts earlier and then shows a memory error).
Code: Select all
*** ZME Z-UNO G2 preprocessor. Platform:Windows Version:0.40b1 ***
BOOTLOADER
Openning port ..............................
Openning port .............................. OK
Syncing with Z-Uno ..............................
Syncing with Z-Uno .............................. OK
------------------------------------------------------------------------------------
Z-Uno board information
------------------------------------------------------------------------------------
FIRMWARE
VERSION: 03.12
BUILD_SEQUENCE: 00002651
BUILD_DATETIME: 2023-04-25T20:11:46(MSK)
SUPPORTED_HWREV: 0704
LIMITS
CODE: 456704 Bytes
RAM: 16384 Bytes
HARDWARE
CHIP_UID: 84 2E 14 FF FE 6A 2C 91
PROD_TIME: 2021-07-08T15:35:11(MSK)
PROD_SN: 72
LOCK: DBG_LOCKED
LICENSE
SUB_VENDOR: 0000
BITMASK: 0000000000000000
FEATURES: []
CRC16: 84f9
NETWORK
HOMEID: ef4ee8a5
NODEID: 0
SECURITY
S2 DSK: 57547-60115-25395-18528-05470-53584-26621-34573
_____
S2 PIN: 57547
QR-Code: 900114262000575476011525395185280547053584266213457300100000000000022000277005280000000780
------------------------------------------------------------------------------------
Using bootloader:C:\Users\duch\AppData\Local\Arduino15\packages\Z-Uno2\hardware\zw_cm4f\3.0.10/bootloaders/zuno_bootloader_HW0704.bin
Loading image ..............................
Writing NVM data [> ] (0%)
(...)
Writing NVM data [=================================================>] (99%)
Writing NVM data .............................. OK
Loading image .............................. OK
Rebooting Chip ..............................
Rebooting Chip .............................. OK
Checking image ..............................
Checking image[* ] ..............................
Checking image[ * ] ..............................
Checking image ..............................
Checking image .............................. ERROR_CODEfe
Error 0 Selected bootloader image doesn't fit to your board!
Closing port ..............................
Closing port .............................. OK
Code: Select all
*** ZME Z-UNO G2 preprocessor. Platform:Windows Version:0.40b2 ***
BOOTLOADER
Openning port ..............................
Openning port .............................. OK
Syncing with Z-Uno ..............................
Syncing with Z-Uno .............................. OK
------------------------------------------------------------------------------------
Z-Uno board information
------------------------------------------------------------------------------------
FIRMWARE
VERSION: 03.12
BUILD_SEQUENCE: 00002651
BUILD_DATETIME: 2023-04-25T20:11:46(MSK)
SUPPORTED_HWREV: 0704
LIMITS
CODE: 456704 Bytes
RAM: 16384 Bytes
HARDWARE
CHIP_UID: 84 2E 14 FF FE 6A 2C 91
PROD_TIME: 2021-07-08T15:35:11(MSK)
PROD_SN: 72
LOCK: DBG_LOCKED
LICENSE
SUB_VENDOR: 0000
BITMASK: 0000000000000000
FEATURES: []
CRC16: 84f9
NETWORK
HOMEID: ef4ee8a5
NODEID: 0
SECURITY
S2 DSK: 57547-60115-25395-18528-05470-53584-26621-34573
_____
S2 PIN: 57547
QR-Code: 9001475080005754760115253951852805470535842662134573001000000000000220002770052800000007800803001
------------------------------------------------------------------------------------
Using bootloader:C:\Users\duch\AppData\Local\Arduino15\packages\Z-Uno2 (Beta)\hardware\zw_cm4f\3.0.12/bootloaders/zuno_bootloader_HW0704.bin
Loading image ..............................
Writing NVM data [> ] (0%)
(...)
Writing NVM data [=================================================>] (99%)
Writing NVM data .............................. OK
Loading image .............................. OK
Rebooting Chip ..............................
Rebooting Chip .............................. OK
Checking image ..............................
Checking image[* ] ..............................
Checking image[ * ] ..............................
Checking image ..............................
Checking image .............................. ERROR_CODEfe
Error 0 Selected bootloader image doesn't fit to your board!
Closing port ..............................
Closing port .............................. OK
Failed to burn bootloader: uploading error: exit status 1