I'm looking for a help.
I used guide https://z-wave.me/support/uzbrazberry-firmwares/ to perform a firmware update, exactly following:
At that page it was shown that my board has 5.27 firmware and that it's possible to update to 5.32.In Expert UI go to Network→Controller Info→Firmware upgrade or directly to IP:8083/expert/#/uzb
So, I started update, after a some time (less than a minute as I remember) notification was shown that it updated successfully.
But once I tried to go to other pages it shows on everywhere:
Checked /var/log/z-way-server.log:An unexpected error occurred while initialising the Z-Wave controller data.
Please check
1.) if the controller is plugged in correctly,
2.) that in the app 'Z-Wave Network Access' the right port is entered
(UZB: '/dev/ttyACM0', RaZberry shield: '/dev/ttyAMA0', UZB-Windows: '\\.\COM3', Z-Stick: '/dev/ttyUSB0', embedded boxes: '/dev/ttyS0' or '/dev/ttyS1')
3.) the app is aktiv. If not you could activate it under Menu > Apps > Active or add a new one under Menu > Apps > Local.
The Setting 'Expert View' needs to be active under Menu > My Settings.
Code: Select all
[2019-01-16 14:02:03.628] [D] [zway] Opened device: /dev/ttyAMA0
[2019-01-16 14:02:03.628] [D] [zway] Worker thread successfully created
[2019-01-16 14:02:03.628] [D] [zway] Worker thread entry point
[2019-01-16 14:02:03.629] [I] [zway] Adding job: Get controller info and supported function classes
[2019-01-16 14:02:03.639] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2019-01-16 14:02:03.841] [I] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2019-01-16 14:02:03.841] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2019-01-16 14:02:04.043] [I] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2019-01-16 14:02:04.043] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2019-01-16 14:02:04.245] [I] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2019-01-16 14:02:04.245] [W] [zway] Job 0x07 (Get controller info and supported function classes) dropped: too many resends
[2019-01-16 14:02:04.245] [D] [zway] Job 0x07 (Get controller info and supported function classes): fail
[2019-01-16 14:02:04.245] [C] [zway] Get Serial API Capabilities returned zero.
[2019-01-16 14:02:04.245] [I] [zway] Removing job: Get controller info and supported function classes
[2019-01-16 14:02:04.255] [D] [zway] Worker thread exit point
[2019-01-16 14:02:04.255] [D] [zway] Worker thread successfully finished
[2019-01-16 14:02:04.267] [E] [zway] SaveData will not save data since it wasn't loaded. This is to prevent data loss.
[2019-01-16 14:02:04.309] [I] [core] Error: Bad data - communication failed
[2019-01-16 14:02:04.312] [I] [core] Tried 5 times without success. Stopping tries.
[2019-01-16 14:02:04.320] [I] [core] Notification: critical (z-wave): Cannot start Z-Wave binding: Error: Bad data - communication failed
I also tried sudo reboot and then sudo halt... neither helped.
Both LEDs (green and red) on a razberry shield are constantly on right after the power on.
What are the ways to fix it?