However, after upgrading firmware the device seems to be completely dead.
z-way-server.log (attached) shows the process seemingly succeeding, ordering a soft reset and terminating the z-wave binding,
Code: Select all
[2020-05-19 21:45:39.722] [I] [zway] Removing job: Soft reset
[2020-05-19 21:45:39.733] [D] [zway] Worker thread exit point
[2020-05-19 21:45:39.734] [D] [zway] Worker thread successfully finished
[2020-05-19 21:45:39.734] [I] [core] Terminating Z-Wave binding
Code: Select all
[2020-05-19 21:45:41.873] [C] [zway] data access without a lock
[2020-05-19 21:45:41.873] [C] [zway] data access without a lock
[2020-05-19 21:45:41.873] [E] [zway] Node 15:0 CC Security: No controller device found
[2020-05-19 21:45:42.003] [I] [core] Trying to restart Z-Wave binding (zway) in 10 seconds
Code: Select all
[2020-05-19 21:46:34.996] [D] [zway] Opened device: /dev/ttyAMA0
[2020-05-19 21:46:34.996] [D] [zway] Worker thread successfully created
[2020-05-19 21:46:34.996] [D] [zway] Worker thread entry point
[2020-05-19 21:46:34.996] [I] [zway] Adding job: Get controller info and supported function classes
[2020-05-19 21:46:35.006] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2020-05-19 21:46:35.208] [I] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2020-05-19 21:46:35.208] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2020-05-19 21:46:35.410] [I] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2020-05-19 21:46:35.410] [D] [zway] SENDING: ( 01 03 00 07 FB )
[2020-05-19 21:46:35.612] [I] [zway] Job 0x07 (Get controller info and supported function classes): No ACK received before timeout
[2020-05-19 21:46:35.612] [W] [zway] Job 0x07 (Get controller info and supported function classes) dropped: too many resends
[2020-05-19 21:46:35.612] [D] [zway] Job 0x07 (Get controller info and supported function classes): fail
[2020-05-19 21:46:35.612] [C] [zway] Get Serial API Capabilities returned zero.
[2020-05-19 21:46:35.613] [I] [zway] Removing job: Get controller info and supported function classes
[2020-05-19 21:46:35.623] [D] [zway] Worker thread exit point
[2020-05-19 21:46:35.623] [D] [zway] Worker thread successfully finished
[2020-05-19 21:46:35.634] [I] [zway] SaveData will not save data since it wasn't loaded. This is to prevent data loss.
[2020-05-19 21:46:35.649] [I] [core] Error: Bad data - communication failed
[2020-05-19 21:46:35.651] [I] [core] Tried 5 times without success. Stopping tries.
[2020-05-19 21:46:35.656] [I] [core] Notification: critical (z-wave): Cannot start Z-Wave binding: Error: Bad data - communication failed
I have done multiple complete power cycles of RPI and am stuck.
Any ideas?