Search found 56 matches
- 22 Dec 2014 21:48
- Forum: Device specific
- Topic: EZMotion PIR detector - any success?
- Replies: 15
- Views: 18217
Re: EZMotion PIR detector - any success?
The final result of all the above operations was the following: The device worked normally, it detected all motion but the strange thing was that it consumed 20 mA of battery power! Please note that I successfully set the wakeup interval to 3600 s - which obviously worked as the device didn't respon...
- 22 Dec 2014 21:43
- Forum: Device specific
- Topic: EZMotion PIR detector - any success?
- Replies: 15
- Views: 18217
Re: EZMotion PIR detector - any success?
3. To finally complete the interview, I forced the re-interview of the failed command classes manually. Here is the log: [2014-12-22 16:06:40.049] [I] [zway] Adding job: SensorBinary Supported Sensor Get [2014-12-22 16:06:40.818] [I] [zway] Adding job: SensorMultilevel Supported Sensor Get [2014-12-...
- 22 Dec 2014 21:42
- Forum: Device specific
- Topic: EZMotion PIR detector - any success?
- Replies: 15
- Views: 18217
Re: EZMotion PIR detector - any success?
Here is part 2 of 2 of the inclusion: [2014-12-22 16:05:21.729] [D] [zway] SETDATA devices.19.data.lastReceived = 0 (0x00000000) [2014-12-22 16:05:21.731] [I] [zway] Node 19:0 CC Version: Battery is v1 [2014-12-22 16:05:21.733] [D] [zway] SETDATA devices.19.instances.0.commandClasses.128.data.versio...
- 22 Dec 2014 21:42
- Forum: Device specific
- Topic: EZMotion PIR detector - any success?
- Replies: 15
- Views: 18217
Re: EZMotion PIR detector - any success?
2. The inclusion stopped again after the interview was fully complete - the device fell asleep during the interview! Here is part 1 of 2 of the inclusion: [2014-12-22 16:05:16.916] [I] [zway] Adding job: Add/re-include node to network [2014-12-22 16:05:16.918] [D] [zway] SENDING (cb 0x0f): ( 01 05 0...
- 22 Dec 2014 21:38
- Forum: Device specific
- Topic: EZMotion PIR detector - any success?
- Replies: 15
- Views: 18217
Re: EZMotion PIR detector - any success?
Hmmm... I still have serious trouble with this device. To being 100% able to rule out the possibility that the batteries might cause the problems, I connected the device to a laboratory power supply with 4.5V (connected to the battery holder). 1. Exclusion worked normally: [2014-12-22 16:00:30.960] ...
- 22 Dec 2014 18:32
- Forum: RaZberry
- Topic: Russian device configuration texts and ZDDX validation error
- Replies: 4
- Views: 5144
Re: Russian device configuration texts and ZDDX validation e
Hmmm... I am not sure about which record I have to blame here. Some (not all, which is even more strange!!!) of these devices show the problem: Fibaro FGS221 V1.9 (App: 1.9, SDK: 4.54.01) Fibaro FGS221 V1.9 (App: 2.1, SDK: 4.54.01) Fibaro FGR211 V1.9 (App: 1.7, SDK: 4.54.01) There may be more but it...
- 16 Dec 2014 23:26
- Forum: Device specific
- Topic: EZMotion PIR detector - any success?
- Replies: 15
- Views: 18217
Re: EZMotion PIR detector - any success?
@PoltoS: Thanks for your reply! But I still do not have ANY luck with it: The device falls asleep during the inclusion process ... I have a secondary RaZberry system (using v2.0.0) for testing here and here is the full inclusion log: [2014-12-16 21:21:35.689] [I] [zway] Adding job: Add/re-include no...
- 16 Dec 2014 23:07
- Forum: RaZberry
- Topic: Russian device configuration texts and ZDDX validation error
- Replies: 4
- Views: 5144
Russian device configuration texts and ZDDX validation error
I am currently running 2.0.1-rc4 but I have seen the same behavior with 2.0.0, too: Some of my devices show Russian texts in the configuration section... how can I change that? I cannot read the Russian language... I also tried to re-select the ZDDX file for those devices manually using the "Se...
- 16 Dec 2014 22:49
- Forum: RaZberry
- Topic: Enable HomeKit and Auth Code for RaZberry
- Replies: 38
- Views: 42274
Re: Enable HomeKit and Auth Code for RaZberry
@pofs: Thanks for the fix but unfortunately, it still does not work... I have tried both 2.0.1-rc1 and 2.0.1-rc4: In both cases I simply get the following error message when entering the PIN from the log output: HomeKitDemo[6072:741973] Error Domain=HMErrorDomain Code=52 "Failed with OSStatus c...
- 16 Dec 2014 09:58
- Forum: RaZberry
- Topic: Thermostatic device
- Replies: 13
- Views: 13471
Re: Thermostatic device
For me, your option 1 is no option. I have bought 4 of the ZWave-Versions of the Danfoss and I have finally and once and for all given up with it. The hardware by itself is fine, so far. However, the firmware has a MAJOR flaw: As soon as this device loses for some reason the contact to the ZWave con...