Where to get the firmware

[herbert-f]

This is okay ...??

Code: Select all

root@raspberrypi:/home/pi# root@raspberrypi:/home/pi# ./ZMESerialUpdater serialapi_uzbupdate -d /dev/ttyAMA0


                                        Z-WAVE Serial API Tool
                                             Version:LWE0.9
                                             by Z-WAVE>ME


-->
Device ready in:1.08714699745 seconds
          FULL INFO
Openning port                            ..............................                            OK


          SERIAL INFO
                 VERSION:  07 1C  VENDOR:  01 47

          ZME_CAPABILITIES
                     UID:  82 CE 2D 6D 56 4C F7 65 8C 07 B2 61 13 A0 D6 00
                  VENDOR:  1D DD   NODES: 83
                   FLAGS:
 B6 0E 07 6B 54 17 E5 F1 43 88 4C 1E 7E 6F 44 1C 0E 07 D8 90 FB 1C EB 79 3A 03 73 F2 CF 6B FE 19
 75 7C 4B B2 11 26 7E 3C CE C4 49 5C

          FIRMWARE CRC
                    BOOT:  FF FF      FW:  FF FF
          MISC
                    FREQ:  EU

                                         NVR Content
          --------------------------------------------------------------------------------------------
          Prog/erase lock :  FF FF FF FF FF FF FF FF, Read back lock: FF
          Rev FF, Cal FF, TXCal  FF FF, SAW  FF FF FF FF, Pin FF, CRC  FF FF
          NMV: CS FF, TYPE FF, SIZE  FF FF, PSIZE  FF FF (EEPROM Unknown)
          USB: VID  FF FF, PID  FF FF, UUID  FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          --------------------------------------------------------------------------------------------
          FACTORY ID: WEEK 255, YEAR 255, CHIP  FF FF, SER  FF FF, WS 255, HWREV: FF FF, CRC8 FF

          elapsed 1.40290999413 seconds

But no UserInterface to flash firmware:

Code: Select all

Controller Info
 The inspect queue will open a second window to allow monitoring the commands sent out by this controller.
Role in Network
Node Id:	
Home Id:	
Primary Role:	No
Primary Capability:	No
SUC/SIS in network:	
Hardware
Vendor:	
Vendors Product ID:	/
Z-Wave Chip:	
Firmware
Library Type:	
SDK Version:	
Serial API Version:	
Capabillities:
UUID:	
Subvendor:	
Nodes limit:	
Controller Static API	
Allow max RF power	
Backup/Restore	
Battery save on sleeping	
Advanced network diagnostics	
Z-Wave Long Range	
Fast communications	
Change vendor ID	
Promiscuous mode (Zniffer)	
Full Zniffer	
RF jamming detection	
Capabillities:	
Software Information
Version number:	
Compile-ID:	
Compile-Date:	
UI
UI version	v1.5.9
Built date	02-04-2022 00:10:16
    
Functions:

I also get an email:
SmartHome UI - Notification
The following notification appeared in Your Z-Way System:
Cannot start Z-Wave binding: Error: Bad data - communication failed
Best Regards
Z-Wave.Me

[PoltoS]

Looks like some internal fields got mangled... Please show me your Z-Way start log. Your board is definitelly fixable remotelly.

[herbert-f]

Do you mean the

z-way-server.log

at /var/log/ ???
I can't find "attachements" at the PM formular???!!!

[PoltoS]

z-way-server.log. Please send to support@z-wave.me and a notice to send to Pavel and PS