I just tried to run an update with the expertui - now my system seems to be broken.
It displays : "The current firmware version is: 5.04 [Bootloader: 48059]"
But commands to my devices fail since I ran the automatic update.
Could you help me which bootloader-files und firmware files I have to upload to get the system alive again?
Updating Razberry
Re: Updating Razberry
Serial updater shows:
SERIAL INFO
VERSION: 05 04 VENDOR: 01 47
ZME_CAPABILITIES
UID: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
VENDOR: 00 00 NODES: 00
FLAGS: 00 00 00 00 00 00 00 00 00 00 00 00 00
FIRMWARE CRC
BOOT: BB BB FW: 52 62
MISC
FREQ: EU
NVR Content
--------------------------------------------------------------------------------------------
Prog/erase lock : FF FF FF FF FF FF FF FF, Read back lock: FF
Rev 01, Cal 03, TXCal 16 11, SAW 0D 3C DE 05, Pin 01, CRC C9 B8
NMV: CS 04, TYPE 02, SIZE 01 00, PSIZE 01 00 (EEPROM M25PE20)
USB: VID 00 01, PID 00 02, UUID 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
--------------------------------------------------------------------------------------------
FACTORY ID: WEEK 33, YEAR 17, CHIP 06 A9, SER 03 69, WS 82, HWREV: 00 01, CRC8 59
elapsed 5.32253503799 seconds
Re: Updating Razberry
Now I managed to run some updates via ssh. And get the following output:
But I still can´t communicate with my devices : "Could not be delivered to Z-Wave stack"
Code: Select all
Z-WAVE Serial API Tool
Version:LWE0.9
by Z-WAVE>ME
-->
Device ready in:3.06252789497 seconds
FULL INFO
Openning port .............................. OK
SERIAL INFO
VERSION: 05 17 VENDOR: 01 47
ZME_CAPABILITIES
UID: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
VENDOR: 00 00 NODES: 00
FLAGS: 00 00 00 00 00 00 00 00 00 00 00 00 00
FIRMWARE CRC
BOOT: FF FF FW: FF FF
MISC
FREQ: EU
NVR Content
--------------------------------------------------------------------------------------------
Prog/erase lock : FF FF FF FF FF FF FF FF, Read back lock: FF
Rev FF, Cal FF, TXCal FF FF, SAW FF FF FF FF, Pin FF, CRC FF FF
NMV: CS FF, TYPE FF, SIZE FF FF, PSIZE FF FF (EEPROM Unknown)
USB: VID FF FF, PID FF FF, UUID FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
--------------------------------------------------------------------------------------------
FACTORY ID: WEEK 255, YEAR 255, CHIP FF FF, SER FF FF, WS 255, HWREV: FF FF, CRC8 FF
elapsed 5.35259699821 seconds
Re: Updating Razberry
Now I managed to Update to the latest firmware 5.39 - I just started again on the terminal and the used the UI.
So this is solved.
So this is solved.
-
- Posts: 1
- Joined: 12 Sep 2023 12:25
Re: Updating Razberry
My operating system is Windows 10 64-bit. The CP2102 USB drivers from silabs.com have been installed.
Arduino has just been reinstalled, and the computer has been reset. Uninstalling/reinstalling the USB driver Rescue mode and factory reset attempts made.
Arduino has just been reinstalled, and the computer has been reset. Uninstalling/reinstalling the USB driver Rescue mode and factory reset attempts made.