I have Z-Way 3.0 installed. After "Start Inclusion" D-Link DCH-Z110 the interview stops at 94%. AssociationGroupInformation" is missing.
I received the following error message (under Experts Page / Association):
Can not configure associations: groups were not reported by the device. Do interview.
Under "Association" in group 1 and 2, I have each entered (#1) Z-Way. And for control "Update from Device" executed.
The interview popular still stands at 94%. In some cases, I could get through expert commands / AssociationGroupInformation / Group 2 / GetName
we're gonna make it to 100%.
But as soon as a new interview is started it stops at 94% again.
With version 2.3.8 D-Link DCH-Z110 was correctly integrated and the interview was finished with 100%.
Z-Way Version 3.0 - Interview buggy
Re: Z-Way Version 3.0 - Interview buggy
In v3.0.0 Z-Way became stricter in Z-Wave protocol (a certification requirement) and devices with bugs in AssociationGroupInformation appears now as not interviewed.
You can bypass it /JS/Run/zway.devices[XXXX].AssociationGroupInformation.data.intervewDone=true
You can bypass it /JS/Run/zway.devices[XXXX].AssociationGroupInformation.data.intervewDone=true
Re: Z-Way Version 3.0 - Interview buggy
That was very helpful. I tried it and the interview is now at 100%. Thank you.
192.x.x.x:8083/JS/Run/zway.devices[6].AssociationGroupInformation.data.interviewDone=true
Output -> true
Interview switches to ->100%
192.x.x.x:8083/JS/Run/zway.devices[6].AssociationGroupInformation.data.interviewDone=true
Output -> true
Interview switches to ->100%
Re: Z-Way Version 3.0 - Interview buggy
Had a similar issue running away 3.0.4 and including a Qubino Flush2 Relay 6.51.09 SDK and AppVersion 5.1 with connected temp.sensor.
It would interview everything except for AssociationGroupInformation in instance 2 [instance 0, 1 and 3 were successful], being stuck at 97%
I had to use this command:
http://xxx.xxx.xxx.xxx:8083/JS/Run/zway ... wDone=true
It would interview everything except for AssociationGroupInformation in instance 2 [instance 0, 1 and 3 were successful], being stuck at 97%
I had to use this command:
http://xxx.xxx.xxx.xxx:8083/JS/Run/zway ... wDone=true
-
- Posts: 1
- Joined: 10 Jul 2020 08:05
- Location: USA
Re: Z-Way Version 3.0 - Interview buggy
Yeah. While including a Qubino flush2 relay 6.51.09 sdk and AppVersion 5.1 with connected temp.sensor. i stuck at 96% later i have completed, now is at 100%. Thank you
-
- Posts: 5
- Joined: 20 Dec 2016 20:32
Re: Z-Way Version 3.0 - Interview buggy
Looking for a little guidance- I have the same issue with an incomplete interview on a GE motion/switch where the interview stops at 92%. The two remaining command classes are AssociationGroupInformation in instance 1 and 2. I tried running the above commands for both instances as such-
http://192.168.4.200:8083/JS/Run/zway.d ... wDone=true
http://192.168.4.200:8083/JS/Run/zway.d ... wDone=true
and the follow-on page does display "true" as output, however on the expert UI it still shows as an incomplete interview. I tried restarting and no change.
Having the same issue with a Schlage BE469ZP door lock. The interview for PowerLevel and Indicator do not complete.
Thanks-
http://192.168.4.200:8083/JS/Run/zway.d ... wDone=true
http://192.168.4.200:8083/JS/Run/zway.d ... wDone=true
and the follow-on page does display "true" as output, however on the expert UI it still shows as an incomplete interview. I tried restarting and no change.
Having the same issue with a Schlage BE469ZP door lock. The interview for PowerLevel and Indicator do not complete.
Thanks-
-
- Posts: 5
- Joined: 20 Dec 2016 20:32
Re: Z-Way Version 3.0 - Interview buggy
Thank you. It helps with correct spelling! Good catch-
Re: Z-Way Version 3.0 - Interview buggy
When is this bug going to be fixed?
Re: Z-Way Version 3.0 - Interview buggy
I believe it is a device bug, the device don't answer to something.
You can send us the log + short description of which interview is not finished and we check it. But if it is on device side, you will have to ask Qubino for an update
You can send us the log + short description of which interview is not finished and we check it. But if it is on device side, you will have to ask Qubino for an update