Hi
I'm new to z-wave. I have an old background in Unix and I'm interested in automation. So I decided to try to setup a Pi 3 with Z-Wave.
I tried with noobs, learned it, switched to jessie. Tried almost all the images available. With no success.
I'm able to setup the PI, connect in Ethernet or WiFi to my network. Able to setup the Z-Wave interface (or Jeedom)
I did all what was recommended to avoid the UART problem. But my Z-Wave network won't work.
I checked the board, the test is OK.
I measured the GPIO pins, voltage is OK.
I think I have an issue with the network. I edited my /etc/hosts. Changed the speed of the TTY, under clocked the PI, nothing works.
Which device tree is the right one to add at the end of /boot/config.txt ?
Is it pi3-disable-bt or pi3-miniuart-bt ?
What could prevent Z-Wave to communicate ?
I have a Raspberry Pi 3 Model B V1.2 2015 with a Z-Wave which looks like a Serie 500. But it looks like a mix between the image of the 300 and the 500 when I look at the images on http://razberry.z-wave.me
Thanks for your help !
Problem with Raspberry Pi 3 / Z-Wave board
Re: Problem with Raspberry Pi 3 / Z-Wave board
Have you tried the RPi 3 image that z-way team put out?
http://razberry.z-wave.me/z-way-server/ ... i3.img.zip
http://razberry.z-wave.me/z-way-server/ ... i3.img.zip
Re: Problem with Raspberry Pi 3 / Z-Wave board
Just downloaded and installed.
Upgraded to 2.2.5 through IP:8084
Done a raspi-confi and set the locale, country, time zone, etc
Connected in ssh under pi@My_local_ip to setup the WiFi (with sudo nano /etc/wpa_supplicant/wpa_supplicant.conf)
Wifi connection works fine.
Connected in admin expert mode.
Added Meteo App, works fine
But Z-Wave still tells me : Cannot start Z-Wave binding: Error: Bad data - communication failed
In Expert mode, under Network / Controller Info, I get Error handling data from server
Tried to send Controllen NIF, got Error handling data
/ZWaveAPI/Run/controller.SendNodeInformation()
I'm stuck. Any idea ?
Upgraded to 2.2.5 through IP:8084
Done a raspi-confi and set the locale, country, time zone, etc
Connected in ssh under pi@My_local_ip to setup the WiFi (with sudo nano /etc/wpa_supplicant/wpa_supplicant.conf)
Wifi connection works fine.
Connected in admin expert mode.
Added Meteo App, works fine
But Z-Wave still tells me : Cannot start Z-Wave binding: Error: Bad data - communication failed
In Expert mode, under Network / Controller Info, I get Error handling data from server
Tried to send Controllen NIF, got Error handling data
/ZWaveAPI/Run/controller.SendNodeInformation()
I'm stuck. Any idea ?
- Z-Wave Support
- Posts: 353
- Joined: 21 Oct 2016 15:49
Re: Problem with Raspberry Pi 3 / Z-Wave board
Hello,
can you send a picture from your Razberry and a picture from Error?
Please check the Port from the Razberry.
Z-Wave Support Team
can you send a picture from your Razberry and a picture from Error?
Please check the Port from the Razberry.
Z-Wave Support Team
Re: Problem with Raspberry Pi 3 / Z-Wave board
Here are the pictures
- Attachments
-
- Razberry
- IMG_3299.jpg (299.34 KiB) Viewed 14130 times
-
- RPI 3
- IMG_3298.jpg (967.99 KiB) Viewed 14130 times
-
- Board mounted
- IMG_3294.jpg (572.78 KiB) Viewed 14130 times
Re: Problem with Raspberry Pi 3 / Z-Wave board
Thank you for helping me !
Which picture of error do you want ? I can post /var/log/z-way-server.log or a screen copy of the various error that I get on my html interface. Just let me know what you want.
Which picture of error do you want ? I can post /var/log/z-way-server.log or a screen copy of the various error that I get on my html interface. Just let me know what you want.
Re: Problem with Raspberry Pi 3 / Z-Wave board
And here a picture of the error
- Attachments
-
- Capture d’écran 2016-11-28 à 22.13.11.png (92.67 KiB) Viewed 14132 times
Re: Problem with Raspberry Pi 3 / Z-Wave board
Hi !
Try a clean install and login as User "pi".
Then Update Raspberry 3 Firmware for stability work with commands:
sudo apt-get install rpi-update
sudo rpi-update
After this, install the zwave Software as pi User:
wget -q -O - razberry.z-wave.me/install | sudo bash
This was the way that helps me
Try a clean install and login as User "pi".
Then Update Raspberry 3 Firmware for stability work with commands:
sudo apt-get install rpi-update
sudo rpi-update
After this, install the zwave Software as pi User:
wget -q -O - razberry.z-wave.me/install | sudo bash
This was the way that helps me
Raspi 3, Zwave.me 4.1.0.
Re: Problem with Raspberry Pi 3 / Z-Wave board
Done as per your instructions
Still getting :
22:20 | Cannot start Z-Wave binding: Error: Bad data - communication failed
Still getting :
22:20 | Cannot start Z-Wave binding: Error: Bad data - communication failed
- Z-Wave Support
- Posts: 353
- Joined: 21 Oct 2016 15:49
Re: Problem with Raspberry Pi 3 / Z-Wave board
Hello,
has you restart you system after installing Z-Way?
Please check the Port and your bootloader in the expert UI.
regards
Z-Wave Support
has you restart you system after installing Z-Way?
Please check the Port and your bootloader in the expert UI.
regards
Z-Wave Support